Thunder Tiger Titan X50 EF - Manual (Page 14)

Control Arm Set / 控制臂組裝
Bag F+I
HME3-18B
SET SCREW,M3x18
無頭內六角螺絲,M3x18
HMC2-4B
SOCKET SRCEW,M2x4
內六角螺絲,M2x4
HNX3-12B
S.B.H SELF TAPPING SCREW
半圓頭內六角自攻螺絲
HMC3-12B
SOCKET SCREW,M3x12
內六角螺絲,M3x12
BK2248
BK2249
HME3-18B
HMC2-4B
BK2271
HNX3-12B
BV2569-R
BV2570-L
BK2279
BK0649-1 BK0088
BK0077
HSA3-10
BK2552
BK0367
BK2529
HMV1680ZZY
HMC2512B
HMM25Z 相位控制導軌
機殼固定鋁柱
無頭內六角螺絲,M3x18
內六角螺絲,M2x4
陀螺儀座
半圓頭內六角自攻螺絲
120° 無平衡翼控制搖臂組(右), 4757
120° 無平衡翼控制搖臂組(左), 4757
內六角連接頭
內六角連接頭螺絲
墊片, d3xD5xW0.5
軸環, d3xD4xW6
半圓頭內六角螺絲, M3x10
尾驅動軸
尾驅動連接棒
傳動軸軸承套
滾珠軸承, d8xD16xW5
內六角螺絲, M2.5x12
止鬆螺帽, M2.5
PHASING CONTROL TRACK
CANOPY RETAINING POST
SET SCREW,M3x18
SOCKET SRCEW,M2x4
GYRO TRAY
S.B.H SELF TAPPING SCREW
120° FB CONTROL ARM SET-R, 4757
120° FB CONTROL ARM SET-L, 4757
HEX POST
LINKAGE BALL
WASHER, d3xD5xW0.5
COLLAR, d3xD4xW6
BUTTON HEAD SOCKET SCREW, M3x10
TAIL DRIVE SHAFT
TAIL DRIVE SHAFT LINKER
TAIL DRIVE SHAFT BRG
BEARING, d8xD16xW5
SOCKET SCREW,M3x12
NYLON NUT,M2.5 1
2
2
2
1
4
1
1
2
4
2
2
2
1
2
1
1
2
2
Left Side
左側
No.
1
2
3
4
5
6
7
8
9
10
Qty Material No. Description 名稱 No.
11
12
13
14
15
16
17
18
19
Qty Material No. Description 名稱
(2)
(1)
(5)
(6)
(6)
(11)
(7)
(12)
(10)
(13)
(10)
(3)
(4) (9)
Apply threadlocker
使用螺絲防鬆膠
(12)
(10)
(10)
(4)
(13)
(11)
(8)
(9)
(3)
(2)
Apply C.A Glue
使用快乾膠黏合
Secure all screws shown on this page with a drop of
thredlocker except the screws #4 and 6.
除螺絲＃4及6之外，本頁顯示之螺絲請使用適量防鬆膠鎖固。
Note the “120L”/”120R” mark on the arms.
請按照控制臂左、右方向安裝。
Nose
機頭
Tail
尾座
350mm / 13.78”
(15)
(14)
(19)
(18)
(18)
(19)
1. 將軸承擠壓入橡膠軸套內。
2. 參考圖示，塗抹些許防鬆膠將尾傳動軸接頭
鎖在尾傳動軸，但勿過度鎖緊。
3. 在尾傳動軸上軸承固定位置前方，塗抹少量
快乾膠，迅速滑動軸承至定位固定；該定位
大約距離軸傳動接頭350mm / 13.78”處。
4. 塗抹些許矽膠油脂或凡士林於橡膠軸套表面
上，稍後將尾驅動軸組裝入尾管時，會較為
容易。
(16)
(17)
The hole with a round chamfer
goes toward the tail。
有倒角的孔徑朝向尾座。
CA
CA
1. Attach the Bearing into the Rubber Bearing Support.
2. Screw the Shaft End onto the Tail Drive Shaft with a drop of threadlocker
as the drawing, but do not over tighten.
3. Add a drop of thin CA glue on the Tail Drive Shaft next to where the
bearing should be, and then slide the bearings over the position quickly;
the distance from the Shaft Drive End to the Rubber Shaft Bearing
Support is approx. 350mm / 13.78”.
4. Apply some amount of silicon oil or Vaseline onto the rubber surface for
easy install into the tail boom later.
HMM25Z
NYLON NUT,M2.5
止鬆螺帽,M2.5
BK0077
COLLAR,d3xD4xW6
軸環,d3xD4xW6
BK0649-1
LINKAGE BALL
內六角連接頭螺絲
Right Side
右側
-13-