Operating instructions – Euro-Pro EP722 User Manual

Page 6

Advertising

OPERATING INSTRUCTIONS

Cleaning & Changing the
HEPA Dust Cup Filter

Crevice Tool, Upholstery and
Dusting Brush

Yellow

Symbol

Red

Symbol

Cord Rewind

Warning:

Hold the plug when rewinding

the cord. Do not allow the cord to whip

when rewinding.

3. To rewind the power cord,

press the cable rewind button

with one hand and guide the

power cord with the other hand to

ensure that it does not whip

causing damage.

Turbine

Tilt
Upwards

Locking Latch

Cleaning Air Driven Turbo Brush

4. Take the HEPA dust cup filter

out of the dust cup, do not let

dust fall out of dust cup.

Warning:

Always unplug the unit from

electrical outlet before opening the Dust

Cup (container).

Crevice Tool
For radiators, crevices,

corners, baseboards and

between cushions.

Important:

Do NOT use the HEPA filter

cartridge without the debris screen in

place.

Dusting Brush
The dusting brush is used for

the furniture, venetian blinds,

books, lamp shades and

shelves.

Upholstery Brush
The dusting brush is used

for the furniture.

Warning

After each Use - Always

remove the Filter Debris Screen from the

HEPA Dust Cup Filter, then vigorously

“TapClean” HEPA Filter until no more

dust can be removed.

5. Take the dust cup and dispose

of the dust inside.

IMPORTANT, Please Note : The

“TapClean” HEPA Dust Cup Filter &

Debris Screen will stop most of the tiniest

dust particles and airborne allergens from

re-entering the air you breathe. In fact it

stops 99.97% of all particles as small as

0.3 microns - many times smaller than a

human hair!!! Because of this incredible

filtration performance, the HEPA Dust Cup

Filter will quickly accumulate, inside the

white filter folds, many fine dust particles

that are difficult to see but which will

eventually block or reduce your suction

power - if not cleaned properly. This can

cause the motor to overheat and the re-

settable thermostat to trip. (Should this

happen turn off the switch, unplug the unit

and allow unit to cool down. Clean the

HEPA Filter and Debris Screen as

described in this section, then reconnect

unit and proceed with vacuuming.)

HEPA Filter

Debris Screen

7. Vigorously “TapClean”

the HEPA Dust

Cup Filter on a

hard surface until no

more dust is observed

falling out from

between the pleats of

the filter. Please note

that on the under side of the HEPA

dust cup filter there is a small brush

which you can use to brush out the

pleats of the filter.

6. Separate the debris screen from the

HEPA filter cartridge by grasping the

debris screen with one hand and the

filter frame with the other and pull

apart.

Warning:

To reduce the risk of electric

shock, the power cord must be

disconnected before removing the dust

cup, dust cup filter,changing the filters or

performing maintenance/trouble shooting

checks.

Power Cord

Your vacuum cleaner includes a power

cord, which is automatically retractable.

To extend your power cord, pull from

rear and extend to desired length.

When cleaning is finished, first switch

off power and disconnect plug from

electrical outlet. Then press on cord

rewind button. If the cord does not fully

retract, pull it out again and then press

on cord rewind button.

Note:

Before using the appliance,

unwind a sufficient length of cable and

Insert the plug into the wall socket. A

yellow mark on the power cord shows the

ideal cable length. Don’t pull the power

cord beyond the red mark.

1. Slide locking latch forward then tilt the

top housing of the brush upwards. The

top housing is hinged and will tilt up

approximately 45° only.

2. Inspect turbine wheel and air passage

for debris and/or blockage. Remove

debris if present.

3. Inspect the rotating brush for built-up

hair or string. If present, remove by

carefully cutting with scissors. Avoid

damaging or cutting bristles.

4. Once clean, close the top cover of the

turbo brush and slide the locking latch

toward the rear of the brush to lock.

1. Push the Power On/Off switch

to the OFF position to

disconnect the power.

2. Remove the flexible hose.

3. Remove the dust cup by lifting

the dust cup handle. See

illustration below.

Power On/Off Button

1. Insert the power plug into the wall

outlet.

2. Press the Power On/Off Switch to

activate the vacuum cleaner.

Dust Cup Handle

8. “TapClean” the Debris

Screen or rinse under

a faucet until clean.

Remember that

the Debris Screen

must be completely

dry before reinstalling

in the vacuum.

Advertising