Eaton Electrical POW-R-COMMAND 1000 - Manual (Page 2)

2 EATON CORPORATION Cutler-Hammer Pow-R-Command 1000 LCD Display Instruction Leaflet IL01412010E Effective: June 2006
LCD Programming Procedure
1. Press any key to begin. The Eaton logo will be displayed:
After a few seconds, the firmware version will be displayed:
After a few more seconds, the initial status screen will be displayed:
Press SEL to get to the MAIN MENU .
2. Login
If user passwords have been created on your system by your distrib-
utor/installer, you will see the following screen. Use
UP/DOWN to
enter the letters of your password and the SEL key to advance to the
next letter. Advance the cursor past the end of the blanks to submit
the password.
If this LCD tool has just been powered up, it will have to download
a database from the PRC1000 controller. You may see the following
screen with the progress indicator:
The database may take up to 10 minutes to download during initial
startup. Afterwards, the
MAIN MENU will be displayed:
3. Set Date/Time/DST/Location
From the MAIN MENU , select Configure Date/Time . The follow-
ing menu will be displayed:
FIRMWARE VERSION A1
Aug 25, 2006 11:28A
Group Status:
ON: ABC N
OFF: DEFGHIJKLM OP
Press SEL for menu
Aug 25, 2006 11:28A
User ID:
________
Aug 25, 2006 11:28A
Refreshing Database
Please wait... 57%
Press BACK to quit
MAIN MENU
Command Groups ON/OFF
Panel Status Screen
Configure Groups
Configure Date/Time _
Group Status:
ON: ABC N
OFF: DEFGHIJKLM OP
Use UP/DOWN to select Change Date . Use SEL to move through the
date digits. Use UP/DOWN to set the month, day and year, respec-
tively. After setting the year, hit SEL one more time. The new values
will be displayed on the PRC1000.
Use UP/DOWN to highlight Change Time . Use SEL to move through
the time digits. Use UP/DOWN to set the hour, minute and AM/PM,
respectively. After setting the AM/PM, hit SEL one more time.
The new values will be displayed on the PRC1000.
Use UP/DOWN to highlight Change DST . Use SEL to start editing the
DST setting. Use UP/DOWN to choose NONE , AUTO or MANUAL . If
MANUAL is chosen, settings for start and end date will appear. Hit SEL
to jump to the start date. Use UP/DOWN to set the month and day
values. Use SEL to move through the digits. After setting the DST
setting (or dates for MANUAL), hit SEL one more time. The new
values will be displayed on the PRC1000.
Use UP/DOWN to highlight Change ASTRO-Loc . Hit SEL to start
editing the location. The following screen will be displayed:
Use UP/DOWN to set the latitude value in degrees. The latitude range
is -90 (South) to +90 (North).
Note: Sunrise/sunset calculations lose accuracy outside the -62 to
+62 range. Hit SEL to move to the longitude setting. Use UP/DOWN to
set the longitude value in degrees. The longitude range is +180
(Alaska) to -180 (Western Pacific). Hit
SEL to move to the timezone
setting. Use UP/DOWN to set the timezone value in hours. The
timezone range is +12 hours (west of GMT) to -12 hours (east of
GMT). After setting the timezone, hit
SEL one more time. The new
values will be displayed on the PRC1000. The RISE and SET times
will update with the new values calculated from the input latitude and
longitude and the screen will return to the
Configure Date/Time
menu. Use BACK to return to the MAIN MENU .
4. Configure Breaker Group A
From the MAIN MENU , select Configure Groups . The following
screen will be displayed:
The group is shown, followed by its current status ( OFF in this
example). The next line is the group description, if it exists ( GROUP A
LIGHTS in this example), followed by the number of loads (breakers)
that has been associated with this group (15 in this example).
CONFIGURE DATE/TIME
Change Date__08/23/06
Change Time 11:37 AM
Change DST MANUAL
St: mm/dd End: mm/dd
Change Astro Loc.
ASTRO LAT: 33.00
LON: 84.00
TIMEZONE: 5
RISE 06:30 SET 07:00
SELECT GROUP
TO CONFIGURE:
Group A GRPA OFF
GROUP A LIGHTS
15 loads in group.
Use up/down/sel to
change selection