ShoreLand'r SLRB40TBBXLW V.1 - Manual (Page 10)

Midwest Industries, Inc. Ida Grove, IA 51445 800.859.3028 www.shorelandr.com
0003463
Page 10 REV A 10/11/06
Install another spring bracket bushing in the front hole
on the rock arm assemblies. Secure with a 9/16” x 3-
1/4” hex bolt and lock nut. Tighten.
Hook the hook end of the springs mounted to the front
axle over the bushing just installed in the rocker arm
assembly. Swing the front of the spring up and attach
the front mounting hole in the spring bracket with an-
other 9/16” x 3-1/4” hex bolt and lock nut.
Tighten all axle U-bolts and spring bolts.
ONE AXLE BRAKE INSTALLATION
Cut the tape securing the brake line hose to the axle.
Remove the brass plug from the port in the brass
block on the right brake caliper. Thread in the brake
hose male end and tighten to 6-8 ft. lb. or else 72-96
in. lb. of torque.
DO NOT OVER TIGHTEN Over tightening will cause
the brass block to crack and then leak.
Place the other end of the hose up through the hole
provided in the brake line clip bracket. Secure in place
with the U-shaped hose clip provided. Remove the
plastic cap from the end of the frame brake line com-
ing out of the side frame by the axle. Carefully uncoil
the brake line so that it will reach the end of the hose
just attached to the brake line bracket. Thread the
brake line fitting into the brake line hose. Tighten.
NOTE: The axle has brake fluid installed in the calipers
and the axle line when it is assembled at the factory.
This is done to protect the inner parts of the brake sys-
tem during shipping and storage. The complete brake
system including the axle MUST be re-bled to ensure
that all air has been removed from the brake system.
For bleeding instructions see either the UFP brake
bleeding manual or the ShoreLand’r Disc Brake
Manual.
Fill the actuator reservoir with brake fluid and bleed
the line per the instructions in the Brake Manual.
DUAL AXLE BRAKE INSTALLATION
If your trailer is equipped with dual axle brakes con-
nect the line to the axle as follows:
Cut the tape securing the brake line hose to the axle.
Remove the brass plug from the port in the brass block
on the right brake caliper. Thread the brake hose male
end into the block and tighten to either 6-8 ft. lb. or 72-
96 in. lb. of torque.
DO NOT OVER TIGHTEN Over tightening will cause
the brass block to crack and then leak.
Attach the brake hoses from the axles to the spring
bracket with the U-shaped hose clip. Once the brake
hoses are secured in place the lines can be attached.
Identify which brake line hose that the side frame
brake line tubing will be connected to. In a dual axle
installation it can connected to either one. When iden-
tified, locate the brass tee connector. Screw the male
port of the tee into the brake line hose. Tighten. Next
connect the side frame brake line into the top port on
the tee. Connect the two axles together using the 40”
brake line supplied. Thread one end of the line into the
brass tee just installed. Route the line over to the other
axle, form a loop in the line and then connect the other
end into the brake line hose for the second axle.
Tighten to 6-8 ft. lb. or 72-96 in. lb. of torque.
DO NOT OVER TIGHTEN Over tightening will cause
the brass block to crack and then leak.
NOTE: The axles have brake fluid installed in the cali-
pers and the axle lines when they are assembled at
the factory. This is done to protect the inner parts of
the brake system during shipping and storage. The
complete brake system including the axle MUST be
re-bled to ensure that all air has been removed from
the brake system.
For bleeding instructions see either the UFP brake
bleeding manual or the ShoreLand’r Disc Brake
Manual.
Fill the actuator reservoir with brake fluid and bleed
the line per the instructions in the Brake Manual.
TIRE & WHEEL ASSEMBLY
Mount the tire and wheel assemblies using the 1/2”
fine threaded tapered lug nuts provided. Tighten to 85-
95 ft./lb. torque using the rotation pattern as shown in
the ShoreLandr’s Owners Manual.
Re-torque the lug nuts after 50 miles driving and then
periodically thereafter.