Edirol 4-CHANNEL V-4 - Manual (Page 91)

91
MIDI implementation
2. MIDI messages transmitted from MIDI
OUT
* If MIDI Thru is ON, MIDI messages received at MIDI IN are re-transmitted without
change from MIDI OUT.
* If MIDI Thru is ON, messages from the V-4 itself will not be transmitted.
■ Channel voice messages
● Control Change
* The messages assigned in MIDI Setup will be transmitted when you operate the panel.
The control changes that can be used are CC#1–5, 7–31, and 64–95. For the factory
settings, refer to “Settings Transmitted/Received Using MIDI” (p. 94).
❍ Bank Select (controller numbers 0, 32)
Status 2nd byte 3rd byte
BnH 00H mmH
BnH 20H llH
mm, ll= bank number:
*
When you select channel A or channel B inputs, make memory settings, or specify how
sub-channels are mixed in Presentation mode, these messages will be transmitted in
conjunction with Program Changes.
* The following controls correspond to each Bank Select message.
Bank Select Program No. Control
MSB/LSB
-------------------------------------------------------------------------------
50H/00H
00H - 07H MEMORY 1-8
-------------------------------------------------------------------------------
00H/00H
00H - 03H A ch, INPUT 1-4
-------------------------------------------------------------------------------
01H/00H
00H - 03H B ch, INPUT 1-4
-------------------------------------------------------------------------------
❍ Modulation (controller number 1)
Status 2nd byte 3rd byte
BnH 01H vvH
❍ Breath-type (controller number 2)
Status 2nd byte 3rd byte
BnH 02H vvH
❍ Foot-type (controller number 4)
Status 2nd byte 3rd byte
BnH 04H vvH
❍ Portamento Time (controller number 5)
Status 2nd byte 3rd byte
BnH 05H vvH
❍ Volume (controller number 7)
Status 2nd byte 3rd byte
BnH 07H vvH
❍ Balance (controller number 8)
Status 2nd byte 3rd byte
BnH 08H vvH
❍ Panpot (controller number 10)
Status 2nd byte 3rd byte
BnH 0AH vvH
❍ Expression (controller number 11)
Status 2nd byte 3rd byte
BnH 0BH vvH
❍ Effect Control 1 (controller number 12)
Status 2nd byte 3rd byte
BnH 0CH vvH
❍ Effect Control 2 (controller number 13)
Status 2nd byte 3rd byte
BnH 0DH vvH
❍ General Purpose Controllers 1–4 (controller numbers 16-19)
Status 2nd byte 3rd byte
BnH 10H - 13H vvH
❍ Hold 1 (controller number 64)
Status 2nd byte 3rd byte
BnH 40H xxH
❍ Portamento (controller number 65)
Status 2nd byte 3rd byte
BnH 41H xxH
❍ Sostenuto (controller number 66)
Status 2nd byte 3rd byte
BnH 42H xxH
❍ Soft (controller number 67)
Status 2nd byte 3rd byte
BnH 43H xxH
❍ Legato (controller number 68)
Status 2nd byte 3rd byte
BnH 44H xxH
❍ Hold 2 (controller number 69)
Status 2nd byte 3rd byte
BnH 45H xxH
❍ Sound Controllers 1–10 (controller numbers 70–79)
Status 2nd byte 3rd byte
BnH 46 - 4FH vvH
❍ General Purpose Controllers 5–8 (controller numbers 80–83)
Status 2nd byte 3rd byte
BnH 50 - 53FH vvH
❍ Portamento Control (controller number 84)
Status 2nd byte 3rd byte
BnH 54H vvH
❍ Effect Depth 2–5 (controller number 92–95)
Status 2nd byte 3rd byte
BnH 5C - 5FH vvH
● Program Change
Status 2nd byte
CnH ppH
pp= program number:00H - 7FH (prog.1 - prog.128)
*
When you select channel A or channel B inputs, make memory settings, or specify how
sub-channels are mixed in Presentation mode, these messages will be transmitted in
conjunction with Bank Select messages. For details, refer to the section on Bank Select.
● Channel Pressure
Status 2nd byte
DnH vvH
* Just as for Control Changes, the messages assigned in MIDI Setup will be transmitted
when you operate the panel. For the factory settings, refer to “Settings Transmitted/
Received Using MIDI” (p. 94).
● Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
mm, ll= pitch bend value:00 00H - 40 00H - 7F 7FH (-8192 - 0 -+8191)
*
Just as for Control Changes, the messages assigned in MIDI Setup will be transmitted
when you operate the panel. For the factory settings, refer to “Settings Transmitted/
Received Using MIDI” (p. 94).
V-4_e.book 91 ページ ２０１０年３月１１日 木曜日 午後１時５１分