Crelando 48450 - Manual

Intended use:
The Rhinestone Setter is intended exclusively for use in dry interior
areas. The Rhinestone Setter is an electric heating tool for fixing
rhinestones onto paper, textile, suede, leather, wood, cork and other
materials by means of heated metal tips. The Rhinestone Setter is
suitable for thermo-glue-coated rhinestones rivets, halves of pearls and
shaped stones. These stones and pearls are provided with a thermo
glue coat on the back side. The glue starts to liquefy already from
approximately 120°C and hence makes the connection between the
material and the stone possible. Any other use is not permitted. Such
use can lead to injuries (burns) of the user and damages of the material.
In these cases, the manufacturer carries no liability.
Safety instructions:
• CAUTION! When not in use, this Rhinestone Setter must be placed
on the security stand (picture VIII).
• When the device is placed on the stand, the surface underneath must
be firm, not flammable and horizontal.
• This appliance is not intended for use by persons (including children)
with restricted physical, sensory or intellectual abilities or lacking
experience and/or lacking knowledge unless they are supervised by
a person responsible for their safety or they receive instructions on
how to use the appliance.
• Children should be supervised in order to ensure that they do not play
with the appliance.
• In order to avoid hazards, if the mains connection of this appliance is
damaged, it must be replaced by the manufacturer or his customer
service or a similarly qualified person.
• A fire can break out if the appliance is not handled carefully.
• Ensure that the connecting cable does not come into contact with
heat, oil or sharp edges. Damaged connecting cables can cause fires,
short-circuits and electric shocks.
• Before use, remove combustible objects, liquids and gases from the
working area of the appliance. Keep your working area clean in order
to prevent accidents.
• Before use, check that the tool tip is correctly attached to the appliance.
The hot tips and their receptacles must not be brought into contact
with skin, hair, etc. Risk of burns.
• After use, place the Rhinestone Setter on the stand and allow it to
cool down before packing it away.
• As long as it is in use, do not leave the appliance unsupervised.
• Do not emerge the appliance into water and do not expose it to
moisture. Risk of electric shock!
• When the appliance is not in use, store it in a safe place protected
from dust and moisture.
• Check the appliance for damage. Do not use if damaged!
• During use, ensure adequate ventilation. Ensure that no poisonous
gases or vapours can be inhaled. Wear protective clothing (e.g. long
sleeved clothing, protective goggles).
• For longer work interruptions, disconnect the appliance from the voltage
source.
• Avoid use of the appliance on all plastic or synthetic material surfaces.
NOT SUITABLE for surfaces of electronic devices, such as e.g. mobile
phones, as the setter reaches a high temperature and may melt the
material and/or the surfaces.
• Do not decorate clothes of small children with rhinestones (small parts
could get swallowed).
• After fixing the rhinestones wash your hands carefully.
• Observe national and international safety, health and work protection
regulations.
Preparation:
Please take your time and read the operating instructions carefully
before putting the appliance into operation and keep the operating
instructions for future reference.
It is not allowed to change settings or make modifications from those
set by the manufacturer. It could be dangerous to change the structure
of the device on your own authority, to remove parts or to use parts
which are not approved by the manufacturer. (If you change the structure
of the device on your own authority you risk e.g. an electric shock, a
short circuit and burns.)
Scope of delivery:
1 Operating Instructions
1 Rhinestone Setter
8 tip-piece-kit for various stone sizes and forms (tool tips)
1 security stand
2 x 200 rhinestones
Please check the goods for completeness
Instructions for Use
No. 48450
Rhinestone Setter Kit
IAN 73860
EN
Explanation of the pictures:
 rhinestone setter
‚ flat tip approximately Ø 5 mm (suitable for all stones smaller than
ø 5 mm).
ƒ flat tip approximately Ø 9,5 mm (suitable for all stones bigger than
ø 5 mm and smaller than ø 9,5 mm).
„ concave tip approximately Ø 7 mm (tip with marking “34”. Suitable
for stones from ø 5 mm to ø 7 mm).
concave tip approximately Ø 5 mm (tip with marking “20”. Suitable
for stones from ø 4 mm to ø 5 mm).
† concave tip approximately Ø 4 mm (tip with marking “16”. Suitable
for stones from ø 3 mm to ø 4 mm).
‡ concave tip approximately Ø 3 mm (tip with marking “10”.Suitable
for stones from ø 2 mm to ø 3 mm).
ˆ concave tip approximately Ø 2 mm (tip with marking “8”. Suitable
for stones smaller than ø 2 mm).
‰ mini iron-shaped tip (suitable for all stones with a big surface –
maximum ø 14 mm).
Š security stand (for safe putting down of the hot Rhinestone Setter).
Explanation of the symbols:
Do not touch the tip of the tool! The tip is very hot! Risk of burns!
Do not emerge the appliance into water and do not expose it to
moisture. Risk of electric shock!
The temperature on tool tip is very high during operation! Risk
of burns!
Do not screw on the tip with force!
Put away the appliance correctly on the stand, if the tip is hot
and the setter is not in use (picture VIII).
CY