Powerplus POW30540 HAMMER DRILL 400W EN - Manual (Page 4)

POW30540
Copyright © 2013 VARO P a g e | 4
5.4 Power tool use and care
§ Do not expect the power tool to do more than it can. Use the correct power tool for what
you want to do. A power tool will achieve better results and be safer if used in the context
for which it was designed.
§
Do not use the power tool if the switch cannot turn it on and off. A power tool with a
broken switch is dangerous and must be repaired.
§ Disconnect the plug from the power source before making adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
§ Store power tools, when not in use, out of the reach of children and do not allow people
who are not familiar with the power tool or these instructions to operate it. Power tools are
potentially dangerous in the hands of untrained users.
§ Maintain power tools. Check for misalignment or jammed moving parts, breakages or any
other feature that might affect the operation of the power tool. If it is damaged, the power
tool must be repaired. Many accidents are caused by using poorly maintained power
tools.
§ Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to jam and are easier to control.
§
Use the power tool, accessories and cutting tools, etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking into
account the working conditions and the work which needs to be done. Using a power tool
in ways for which it was not intended can lead to potentially hazardous situations.
5.5 Service
§
Your power tool should be serviced by a qualified specialist using only standard spare
parts. This will ensure that it meets the required safety standards.
6 MACHINE-SPECIFIC SAFETY WARNINGS
§ Use appropriate detectors to determine if utility lines are hidden in the work area or
the local utility company for assistance.
§ Switch off the power tool immediately when the tool insert jams. Be prepared for high
reaction torque that can cause kickback.
§ Hold power tool by the insulated gripping surfaces, when performing an operation
the cutting tool may run into hidden wiring.
§ When working with the machine, always hold it firmly with both hands and provide
secure stance.
§ Secure the work piece.
§
Keep your workplace clean.
§
Always wait until the machine has come to a complete stop before placing it down.
§
Before any work on the machine (e. g., maintenance, tool change, etc.) as well as
transport and storage, set the rotational direction switch to the centre position.
7 FEATURES
7.1 Keyless chuck
Your drill has a keyless chuck that allows you to hand tighten or release drill bit in the chuck
jaws.
The SDS-Plus tool holder allows for simple and convenient changing of
drilling tools without the use of additional tools.
EN
www.varo.com
Do not expect the power tool to do more than it can. Use the correct power tool for what
safer if used in the context
Do not use the power tool if the switch cannot turn it on and off. A power tool with a
ents, changing
accessories, or storing power tools. Such preventive safety measures reduce the risk of
Store power tools, when not in use, out of the reach of children and do not allow people
the power tool or these instructions to operate it. Power tools are
Maintain power tools. Check for misalignment or jammed moving parts, breakages or any
f the power tool. If it is damaged, the power
tool must be repaired. Many accidents are caused by using poorly maintained power
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
Use the power tool, accessories and cutting tools, etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking into
be done. Using a power tool
in ways for which it was not intended can lead to potentially hazardous situations.
Your power tool should be serviced by a qualified specialist using only standard spare
utility lines are hidden in the work area or call
prepared for high
surfaces, when performing an operation where
ands and provide for a
complete stop before placing it down.
tool change, etc.) as well as during
switch to the centre position.
Your drill has a keyless chuck that allows you to hand tighten or release drill bit in the chuck
mple and convenient changing of