Epson EXPRESSION 10000XL - Manual

Start Here
Install the Software
Wait! You must install your software before connecting the scanner to
your computer. The installation may take several minutes. Be sure to close
all open programs and turn off any virus protection programs.
EPSON Scan works with Windows ® Vista, ™ XP, and 2000, and Macintosh ®
OS X 10.2.x, 10.3.9 to 10.4.x. Follow the steps in the section for your
operating system.
Windows
1 Insert the Scanner Software CD-ROM in your CD-ROM or DVD drive.
With Windows Vista, if you see the AutoPlay window, click Run
Epsetup.exe. When you see the User Account Control screen, click
Continue.
2 Read the license agreement and click Agree. The Software Installation
screen appears.
Epson Expression ® 10000XL
3 Click the Install button.
4 When you see a message that installation is complete, click Exit.
5 Follow the on-screen instructions to register your scanner, then remove
the CD-ROM.
If you want to use any of the bonus software included with your scanner,
insert the CD-ROM for the software you want to install, and follow the
on-screen instructions. Some software may not be compatible with
Windows Vista.
Macintosh OS X
1 Insert the Scanner Software CD-ROM in your CD-ROM or DVD drive.
2 Double-click the Epson CD-ROM icon on the desktop.
3 Double-click the Epson icon.
4 Read the license agreement and click Agree.
5 When you see this screen, click the Install button.
6 Enter your name and password, if required, then click OK. Read the
license agreement and click Accept.
7 When you see this screen, click Install.
8 When the installation is done, click Quit.
9 When you see a message that installation is complete, click Exit.
10 Follow the on-screen instructions to register your scanner, then remove
the CD-ROM.
If you want to use any of the bonus software included with your scanner,
insert the CD-ROM for the software you want to install, and follow the
on-screen instructions.
Install the Transparency
Unit
If you have the Photo version of the scanner, you need to install the
transparency unit.
1 Fully open the scanner’s document cover, then lift it straight up.
2 Lower the transparency unit onto the scanner, so that the pins fit into
the holes as shown.
3 Use a coin to turn the transportation lock to the Unlock position.
4 Close the transparency unit.
5 Connect the transparency unit cable to the scanner’s OPTION port, then
tighten its screws.
Turn over
2
Connect the Scanner
Note: If you are installing the optional Network Image Express card, see the
instructions in the User’s Guide.
1 Connect the scanner to your computer.
If you’re using USB . . .
Plug the square end of the USB cable into the scanner’s
USB port. Then plug the flat end into any available USB port
on your computer or USB hub.
If you’re using IEEE 1394 (FireWire ® ) . . .
Plug one end of the IEEE 1394 cable (not included) into the scanner’s
IEEE 1394 port. Then plug the other end into the IEEE 1394 port on
your computer.
2 Slide the transportation lock (the tab over the AC connector) up to the
Unlock position.
3 Plug the scanner’s power cord into the AC connector. Then plug the
other end into a grounded electrical outlet.
4 Press the power button on the front of the scanner to turn it on. The
green Ready light blinks for about 30 seconds during initialization, and
then stays on when the scanner is ready to use.
Caution : If you turn off the scanner, wait at least 10 seconds before turning
it back on.
4
Power button
3
Unpack Your Scanner
1 Remove everything from the box.
If you have the Photo version of the scanner, the following items are
also included.
2 Remove all the tape and packing material inside and around the
product.
1
Scanner
Scanner
Software
CD-ROM
Adobe ®
Photoshop ®
Elements
CD-ROM
MonacoEZcolor ®
CD-ROM
Power cord USB cable
User’s Guide
LaserSoft Imaging ™
SilverFast ® Ai 6
CD-ROM
Transparency
guide
Film holders
(two of each type)
Transparency
unit
Ntmg_SH_E_CPD18060R1.indd 1 2/21/07 9:27:30 AM