Euro-Pro V1055H - Manual (Page 6)

OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS
2. Remove the filter assembly from the
dust cup container.
3. To separate the filter assembly, hold
the bottom of the filter frame and
pull the HEPA-Type filter out.
(Fig. 9)
How to Start
The vacuum can be used on multiple
types of carpeting or bare floors. When
using the crevice tool or dusting brush,
place the handle of the vacuum in the
upright position.
1. Plug the power cord into the electrical
outlet.
2. Push the On/Off
button to the "On"
position to turn
the vacuum on.
3. To release the
handle, step
on the handle
release pedal
and pull back handle.
4. When using the crevice tool or dusting
brush, the vacuum must be in the
upright position. (Fig. 4)
Store or use
attachments
Use
Clean under
furniture
Handle release
Warning: To reduce the risk of electric
shock, the power cord must be
disconnected before removing the dust
cup (container), dust cup HEPA-Type
filter, changing the pre-motor filter or
performing maintenance/trouble shooting
checks.
Important: Do NOT use the vacuum
without ALL the filters in place.
The “Dust Cup (Container)” must always
be emptied when the dirt level reaches
the “FULL" line on the dust cup
(container). To remove the dust cup
(container) from the vacuum:
1. Press down on the dust cup
release button that is located on the
dust cup cover handle of the dust
cup. (Fig. 6)
Removing & Emptying Dust Cup
(Container)
Place unit in “UPRIGHT" position when
using attachment or hose to prevent
possible floor damage. Always set the
carpet height selector to “highest”
setting when using the accessories and
hose.
Attention : Special care is required
when vacuuming certain types of carpet
or floor covering. Always check the
carpet or floor covering manufacturer's
recommended cleaning instructions
before vacuuming.
Carpet Height Selector
This upright vacuum can be used on
multiple types of carpeting and bare
floors. To select a pile height setting:
1. Turn vacuum cleaner "Off".
2. Select a pile height setting by
rotating the carpet height selector
to the desired setting. (Fig. 5)
Carpet height
selector
HIGH: shag carpet, long pile, plush
scatter rugs, tools
MED: medium to long pile
LOW: very low pile, bare floors
Suggested Pile Height Setting:
You may need to raise the height of the
vacuum to make some jobs easier,
such as scatter rugs and longer pile
carpets. Suggested settings are:
Fig. 4
Fig. 5 Dust Cup
Release Button
Fig. 6
2. To empty the dust cup container,
hold the dust cup from the handle
over a garbage container and press
on the trap door release button that is
on the back side of the dust cup
container to release the dust cup
bottom. (Fig. 7) Fig. 8
Open
Mark
Arrow
for
alignment
• The dust cup container can be
washed in lukewarm water.
• Do not use strong detergents.
• Ensure that the dust cup container
is fully dry before putting back on
the vacuum cleaner.
• Do not wash in dishwasher.
IMPORTANT , Please Note: The
Rinseable “TapClean” HEPA-Type Dust
Cup Filter will quickly accumulate many
fine dust particles inside the white filter
folds that are difficult to see but which will
eventually block or reduce your suction
power - if not cleaned properly. Clean the
HEPA-Type Filter after each use as
described in this section.
Warning : After each Use - Always
remove the Filter Assembly, then
vigorously tap clean the HEPA-Type
Filter until no more dust can be
removed.
Fig. 7
Trap Door
Release Button
Cleaning the HEPA Filter and the
Filter Frame
1. To remove the filter assembly from
the dust cup, hold the dust cup
cover from the handle in one hand
and with the other hand, turn the
dust cup container counter
clockwise. (Fig. 8)
4. Remove the filter ring that is
around the
HEPA-Type
filter. Then
vigorously
“TapClean” the
HEPA-Type Filter on a hard
surface until no more dust is
observed falling out.
5. To clean the filter
frame, we
recommend that
you rinse it under
lukewarm running
water to remove
the dirt that
accumulates
on it, but always
allow 24 hours to air dry before
inserting back into the vacuum.
6. To re-assemble the filter
assembly, insert the filter ring over
the HEPA-Type filter and then
insert the HEPA-Type filter
assembly into the filter frame.
Replace the filter assembly into
the dust cup container. Replace
the dust cup container cover.
HEPA-Type
Filter
Filter
Frame
Filter
Ring
Filter Assembly
Fig. 9
6 5