Sealey SPB57T - Manual

InstructIon MAnuAL for:
BROADCAST SPREADER 57kg TOW
BEHIND
MoDEL no: SPB57T
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
3. SPECIFICATION & CONTENTS
2. INTRODUCTION
4.1. check contents against fig.1 above, if anything is missing or
damaged contact your local sealey dealer.
4.2. refering to fig.2, place an axle bush (18) onto the axle of the
frame tube assembly(1).
4.3. Attach the pneumatic wheel (5) then a Ø16 flat washer (17) to
the mounting tube axle. secure with split pin (11) and repeat
procedure for the other side. Additional Ø16 flat washers (17) are
provided to adjust the spacing between the axle bushing (18)
and the pneumatic wheel (5).
4.4. rotate one pneumatic wheel (5) so that the hole on the inside of
the wheel boss aligns with the corresponding hole in the axle
tube. Insert inner hex bolt M5x45 (10) through the axle tube and
secure with lock nut M5 (12) as shown in figure 2.
4. ASSEMBLY
Model No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPB57T
capacity (Weight). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57kg
capacity (Volume) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60ltr
spread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3.6mtr
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6kg
Dimensions (W x D x H). . . . . . . . . . . . . . . . . . .680 x 980 x 790mm
 Ensure that the spreader is in sound condition and good working
order before use.

Ensure that the operator is fully trained and competent to operate
the prime mover before attaching and using the spreader.

Ensure that all chemical safety instructions are adhered to when
handling products for use in the spreader. A full range of personal
safety equipment is available from your sealey dealer.

Always distribute the load evenly.
 Ensure all non essential personnel keep a safe distance when the
spreader is in use.

replace or repair damaged parts. Use only recommended parts.
Unauthorised parts may be dangerous and will invalidate the
warranty.

Keep hands and feet away from moving parts.
 DO NOT overload the spreader - see specification.
 DO NOT leave unattended, especially when loaded, unless the
wheels are chocked or the spreader is otherwise secured.

DO NOT allow others to ride on the spreader.
 DO NOT allow untrained personnel to use the spreader.
 DO NOT use the spreader for purposes other than for which it is
designed.

DO NOT operate the spreader when you are tired or under the
influence of alcohol, drugs or intoxicating medicines.

When loaded, DO NOT operate the spreader over edges, rough
surfaces etc. where the spreader is at risk of overturning.
 WARNING! failure to comply with these instructions may result
in damage to spreader or other property and/or personal injury.
Manufactured with a strong tubular steel frame and polypropylene
dispensing hopper. Pin hitch design attaches to ride-on lawnmowers,
can be converted to ball hitch using Model no. tB36. fitted with
aluminium gear, rain cover, pneumatic tyres and adjustable feed
system. Includes hopper screen to ease spreader flow and filter out
unwanted contaminants. sprays in 360° motion to cover a large area.
suitable for a variety of horticultural agents, including grit, seed, salt,
fertiliser and weed killer.
Original Language Version sPB57t Issue: 2(I) - 17/09/13
fig.1
fig.2
© Jack sealey Ltd