Sealey CH28110VS - Manual (Page 3)

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
FAULT DESCRIPTION SUGGESTED SOLUTION
HEATER DOES NOT OPERATE • Check power supply/trip.
• Check for damage or misalignment.
• Check all wiring connections.
OTHERS Consult a qualified electrician or contact a Sealey authorised dealer.
6. TROUBLE SHOOTING
7. MAINTENANCE
Parts support is available for this product. To obtain a parts listing and/or diagram,
please log on to www.sealey.co.uk, email [email protected] or telephone 01284 757500.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as
waste. All tools, accessories and packaging should be sorted,
taken to a recycle centre and disposed of in a manner which
is compatible with the environment.
WEEE Regulations.
Dispose of this product at the end of its working life in compliance
with the EU Directive on Waste Electrical and Electronic Equipment.
When the product is no longer required, it must be disposed of in an
environmentally protective way. Contact your local solid waste
authority for recycling information.
Original Language Version CH28110V Issue: 2(l) 12/06/15 © Jack Sealey Limited
5. OPERATION
Fig.3
ELECTRICAL TEST, MAINTENANCE & STORAGE WARNING: THIS IS A CLASS 1 TESTED APPLIANCE
 When earth bond testing, the readings should be 0.10Ω and below.
 Disconnect from the mains and allow to cool before moving or attempting any cleaning or maintenance.
 Clean the heater and guard with a damp cloth and some mild detergent.
 When not in use, store the heater carefully in a safe, dry, childproof location.
 To replace any of the elements, contact your authorised Sealey dealer.
 Use a vacuum cleaner outside grille guard to clean dust from heater elements.
 DO NOT touch the elements unless essential to do so.
 DO NOT perform a flash test, as this will reduce the life of the elements.
 DO NOT use abrasive cleaners or polishes on casing or guard.
 WARNING! Ensure you read, understand and apply the safety instructions in Section 1 before using the heater.
NOTE! The ceramic element is fragile and therefore it is important that it is not subjected to any unnecessary shocks or vibration and is not
moved when it is on or until cooled down.
5.1 Ensure the heater is at least 2m from any object.
5.2 Plug in the heater and switch it on.
5.3 The heater has the following settings: See (Fig.3).
Position 0:0 Off position.
Position I:0 Upper element only.
Position 0:I Lower element only.
Position I:I Both elements.
5.4 When the heater is no longer required, switch off and unplug the unit.
IMPORTANT: DURING RELOCATION, THE HEATER SHOULD REMAIN SWITCHED OFF AND DISCONNECTED FROM THE POWER
SUPPLY.
In the event of the heater being knocked over, a safety cut-out switch, which activates at an angle of 35º ±10º,
will disable the heater.
Follow these steps to re-start the heater.
a) Switch ‘off’ the heater at the on/off switches. As (Fig.3).
b) Disconnect the power cord from the power supply.
c) Return the heater to a standing position.
d) If no damage has occurred to elements, replace safety guard if applicable, re-connect power cord to the
power supply and switch the heater back on.
Should the power cord require replacement, a complete wiring loom should be purchased and fitted by a
suitably qualified person.
Off
Off
On
On