Elektra Beckum UK 220 - Manual (Page 10)

19
ENGLISH
•
Before cutting a workpiece to size
make trial cuts with pieces of scrap.
•
Always place a workpiece on the
saw table in such way that it can not
tilt or rock (e.g. always place a
curved board on the table with the
convex side up).
•
When working long stock use suita-
ble supports, such as table rear or
side extensions (optional accesso-
ries).
•
To simplify repetitive cut-off work
use a stock stop (optional acces-
sory).
•
Keep surfaces of saw table and saw
base clean – in particular, remove
resin residue with a suitable clean-
ing and maintenance spray (optional
accessory).
For special tasks the following accesso-
ries are available at your specialized
dealer – see back cover for illustrations:
A Workstand
Provides for a secure machine
stand and optimal working height;
ideal in mobile use, folds up for sav-
ing space.
B Base System Rail
Required for the installation of Slid-
ing Carriage, Table Side or Table
Rear Extension.
C Base System Rail Extension
To extend the Base System Rail to
1350 mm. The enclosed support
leg provides for a firm stand.
D Support leg for Base System Rail
Extension
Provides extra support for the Base
Systen Rail Extension.
E Sliding Carriage with Mitre Fence
For installation on the Base System
Rail. Capacity before the blade up
to 600 mm.
F Table Side Extension
For installation on the Base System
Rail. Extents the saw table to the
left or right.
G Rear Table Extension with support
leg
For installation on the Base System
Rail. Extents the saw table at front
and/or rear by 1000 mm.
H Work Clamp
For cutting accuracy, required for
cutting round stock and non-ferrous
metals.
I Dust Collection Attachment
Helps to protect your health and to
keep the shop clean.
J Suction Adapter
To connect a shop vacuum to the
dust collection attachment.
K Roller/Ball Transfer Stand
For accurate guiding of long stock.
L Care and Maintenance Spray
To remove resin residue and pre-
serve metal surfaces.
M TCT Saw Blade
210x2.2/1.4x30 30 ATB
For rip and cross cuts in grown tim-
ber and particle board.
N TCT Saw Blade
210x2.2/1.4x30 42 ATB
For rip and cross cuts in panels;
plastic, aluminium, copper extru-
sions and high-grade veneered
sheets.
O TCT Saw Blade
210x2.2/1.4x30 64 ATB
General purpose blade for plastics
and metals.
P TCT Saw Blade
210x2.4/1.8x30 40 ATB 0
°
General purpose blade for plastics
and metals.
Danger!
Repairs to electric tools must
be carried out by qualified electri-
cians only!
Electric tools in need of repair can be
sent to the service centre of your coun-
try. Refer to the spare parts list for the
address.
Please attach a description of the fault to
the electric tool.
The saw's packaging can be 100 %
recycled.
Worn out electric tools and accessories
contain considerable amounts of valua-
ble raw and plastic materials, which can
be recycled.
These instructions are printed on chlo-
rine-free bleached paper.
Danger!
Before carrying out any fault
service or maintenance work always:
1. switch machine OFF;
2. unplug power cable;
3. wait for saw blade to come to
standstill.
Check to see that all safety devices
are operational after each fault serv-
ice.
Motor does not run
Undervoltage relay tripped by power fail-
ure:
−
switch on again.
No mains voltage:
−
check cables, plug, outlet and mains
fuse.
Motor overheated, e.g. by a blunt saw
blade or chip build-up in the chip case:
−
eliminate cause for overheating,
wait for a few minutes, then start
saw again.
Stated top speed is not reached
Motor supply voltage too low:
−
use a shorter extension cable or
extension cable with larger lead
cross section
(
≥
1.5 mm
2
).
−
Have power supply checked by a
qualified electrician.
Loss of cutting performance
Saw blade blunt (possibly tempering
marks on blade body):
−
replace saw blade (see section
"Maintenance").
Chip ejection tube blocked
No dust collector hooked up or suction
capacity insufficient:
−
connect dust collector or
−
increase suction capacity (air speed
≥
20 m/sec at chip ejection tube).
Radial pull action not working prop-
erly
Compensation of motorhead carriage
incorrectly set.
−
Set compensation (see section
"Maintenance").
Motorhead carriage slowed down by
saw dust.
−
Clean motorhead carriage guide
elements.
10. Tips and Tricks
11. Available Accessories
12. Repairs
13. Environmetal Protection
14. Trouble Shooting