Document Outline

• Important Safety Instructions
• 1.0 Introduction
  • 1.1 Compatibility With Liebert Equipment
    • Table 1 Liebert IntelliSlot card communication protocols
  • 1.2 Web Support
  • 1.3 Password Protection
  • 1.4 SNMP Support
  • 1.5 Liebert Nform™ Support
  • 1.6 Liebert MultiLink™ Support
  • 1.7 Liebert SiteScan® Web With Modbus Support - IS-WEB485ADPT only
• 2.0 Installation
  • 2.1 Install a Liebert IntelliSlot Web Card-Non-Adapter Version
    • 2.1.1 Connect the Cable
    • 2.1.2 Prepare the Card for Configuration
      • Table 2 Communication settings
  • 2.2 Install a Liebert IntelliSlot Web/485 Card With Adapter
    • 2.2.1 Connect the Cable
    • 2.2.2 Prepare the Card for Configuration
      • Table 3 Communication settings
• 3.0 Configuration Overview
  • Table 4 Configuration interfaces
  • 3.1 Guide to Configuration
    • Table 5 Guide to configuration details
  • 3.2 Open the Terminal Emulation Interface - Serial Connection
    • Table 6 Communication settings
  • 3.3 Open the Terminal Emulation Interface - TCP/IP Connection
  • 3.4 Open the Telnet Interface
  • 3.5 Open the Web Interface
  • 3.6 Saving Changes and Reinitializing the Web Card
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
• 4.0 System Information
  • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Table 7 System information identifiers
  • Web Interface
• 5.0 Network Settings
  • Table 8 Network Settings menu guide
  • 5.1 Boot/IP Settings
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 9 Boot/IP settings range
    • Web Interface
  • 5.2 Domain Name Server (DNS) Settings
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 10 Domain Name Server settings
    • Web Interface
  • 5.3 Management Protocol
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 11 Management protocol ranges
    • Web Interface
      • SNMP Communications Menu
        • Table 12 SNMP communications menu
      • Display/Modify Communities
      • Display/Modify Trap Communities
  • 5.4 Web Server
    • 5.4.1 Specify Web Server Settings
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 13 Web server settings
    • Web Interface
    • 5.4.2 Install Security Certificates - Internet Explorer 6 or earlier
    • 5.4.3 Install Security Certificates - Internet Explorer 7 or later
  • 5.5 Telnet Server
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
  • 5.6 Time (SNTP) Menu
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 14 Time Server parameters
    • Web Interface
  • 5.7 Change Username / Password
    • Table 15 Factory default passwords
    • Table 16 Username and password guidelines
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
  • 5.8 Reset Authentication to Factory Defaults
    • Table 17 Factory default passwords
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
• 6.0 Messaging
  • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Table 18 Messaging menu guide
  • Web Interface
  • 6.1 E-Mail Configuration
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 19 E-mail configuration guide
    • Web Interface
  • 6.2 SMS Configuration
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 20 SMS configuration guide
    • Web Interface
  • 6.3 Customize Messages
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 21 E-mail and SMS message guidelines
    • Web Interface
      • Message Consolidation Time Limit
• 7.0 Factory Settings
  • 7.1 Reset to Factory Defaults
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
  • 7.2 Liebert DS - Local Node Settings for Multiple Cards
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
      • Table 22 Factory default MAC addresses
• 8.0 Monitor and Control Functions - Web Only
  • Web Interface Only
  • 8.1 Monitoring Liebert Equipment
  • 8.2 Controlling Liebert Equipment
    • Table 23 Control operations parameters-functions vary by Liebert unit
  • 8.3 Event Log
    • Event Log Controls
    • Links
• 9.0 Support Information
  • 9.1 View Web Card Information
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
  • 9.2 Events and Parameters
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
• Appendix A - Firmware Updates
  • A.1 Introduction
    • A.1.1 Overview
      • Table A1 Overview of the upgrade process
    • A.1.2 Estimated Time to Download the Firmware Upgrade File
      • Table A2 Estimated Time for downloads
  • A.2 Connect to the Card - Terminal Emulation, Telnet or Web Interface
    • A.2.1 Open the Terminal Emulation Interface - Serial Connection
      • Table A3 Communication settings
    • A.2.2 Open the Terminal Emulation Interface - TCP/IP Connection
    • A.2.3 Open the Telnet Interface
    • A.2.4 Open the Web Interface
  • A.3 Preparing to Update Liebert IntelliSlot Firmware
    • A.3.1 Requirements to Update the Liebert IntelliSlot Card’s Firmware
    • A.3.2 Determine the Liebert IntelliSlot Card Type and Firmware Version
    • Terminal Emulation (Serial or TCP/IP Connection) / Telnet
    • Web Interface
    • A.3.3 Download the Firmware Upgrade File to the Computer
    • A.3.4 Choose a Method to Install the Firmware Upgrade
  • A.4 Updating the Firmware - HTTP (Web) Method
    • A.4.1 Install the Firmware Upgrade
  • A.5 Updating the Firmware - TFTP (HyperTerminal, Telnet, Web) Method
    • A.5.1 TFTP Method - Terminal Emulation / Telnet Interface
      • Open a Connection to the Card
      • Specify TFTP Server and Upgrade Filename
        • Table A4 Firmware update settings - TFTP
      • Reconnect to the Card
      • Begin the Upgrade Process
    • A.5.2 TFTP Method - Web Interface
      • Open a Connection to the Card
      • Specify TFTP Server and Upgrade Filename
        • Table A5 Firmware update settings - Web
      • Reconnect to the Card
      • Begin the Upgrade Process
  • A.6 Updating the Firmware - Xmodem (Serial) Method
    • Connect a Cable to the Serial Ports
      • Figure A1 Null connection
    • Open a Terminal Emulation Connection
    • Change the Baud Rate to 115200
    • Download the First Firmware Update File
    • Download the Second and Third Firmware Update Files
    • Complete the Upgrade and Restore Communication Rate