COLBOR CL100X Bi-Color LED Video Monolight User Manual

Cl100x

Advertising
background image

Thank you for choosing COLBOR product. Please read this manual
carefully before use and follow all instructions mentioned herein.

CL100X

Video Light

User Manual

Safety Instructions

Please read and fully understand this manual before using the product.

Please remove the COB protective film to avoid damage by overheat before

first use.

Please remove the COB protective cover to avoid damage by overheat

before every use.
Do not use the product under moist environment or with wet hands. Do not

allow the product to be splashed or soaked in water.
Keep the product away from corrosive chemicals and liquid to avoid

damage.
Keep the product out of children’s reach during use. Do not leave the

product unattended.
When the product is working, the COB and heat sink will produce high

temperature. Do not block, turn upside down and touch with hands.
To ensure the service life, the cooling system still runs for a while after

shutdown until the COB is below 45℃ .

Please disconnect the power supply and put away the power cord when it is

not in use.

During use, arrange the power cord in order to avoid tripping and cutting off

the power or damaging the product.
Let the product cool completely before storage. Remove the power cable

from the product and put it in the corresponding position of carrying bag

after cooling down.
Do not disassemble the product by yourself, otherwise the warranty will be

invalid. If any fault occurs, please refer it to an authorized technician for

inspection or maintenance.
Recommend to use the original parts of COLBOR. If the product is damaged

due to the use of the non-original parts, it is not included in the warranty of

our products.

Drop or external impact may cause product failure. Artificial damage is not

covered by warranty.

COLBOR reserves the right of final interpretation of the products. The

product design and specifications are subject to change without notice.

Product Instructions

① COB Bead
② Bead Radiator (Air Outlet)
③ Bowen Mount Adaptor (BAR1)
④ Ejector Pin
⑤ Rail
⑥ Air Vent (Air Intake)
⑦ Quick-mount Holder (EC Stand)
⑧ LCD Display Screen

⑨ Brightness Control Wheel
⑩ Color Temperature Control Wheel
⑪ Setting (SET) Button
⑫ Light Effect Frequency (RATE) Button
⑬ Light Effect Mode (EFF) Button
⑭ Color Temperature Mode (CCT) Button
⑮ Type-C Power Input
⑯ Switch Button

Installation & Disassembly

Hold the COB protective cover and pull it out as the

arrow shows.
Note: Make sure remove the cover before every use

to avoid heat damage.

Power adapter (PA120) and V-port battery power cable (VC50) are only

for powering CL100X and CL100XM, not for other electronic devices. If any

damage caused by the wrong use, it is not within our warranty.

① Align the inner frame of adapter ring with the outer frame of light, and

push the adapter ring into the light from the head. Fasten two marbles on the

adapter ring to the chute.
When disassembling, push the adapter ring towards the head of the light.

① Slide the quick-mount holder into the chute under the light and rotate the

knob a tightly.

② Install tripod into the quick-mount holder and rotate the knob b tightly.
③ Adjust the light to the desired angle and rotate the knob c tightly.

Slide the rail of one light into the chute of the other until the pins inlay.

When disconnecting, slide the light out of the chute.

Slide VM2 into the chute of light, determine the fixed position and adjust the

lever to lock.

When removing, adjust the level to unlock and slide out of the light.

(1) Fixing power cables

Screw the power cable fixing clip, put the

cable into the groove, and then align the

bracket with the tightening screw.

(2)DC power supply

Connect power adapter with Type-C power

input and turn on.

(3) Battery power supply

Turn on power after installing V-mount and battery.

Operation Instructions

1. Remove COB protective cover

2. Install adapter and reflector

3. Fixing of the video light

4. Multi-light connection & disassembly

5. Install VM2

6. Power supply

1. Before using the product for the first time, please be sure to tear off the

protective film in front of the COB bead.

2.

Power On:

connect the power cord with the power adapter, plug the

connector of adapter into the fixture’s power input, then attach to an

electricity supply.
3.

Function:

long press the power button, then the power button lights up. The

product enters operation interface.
(

Factory default mode:

CCT)

4.

Power Off:

press the power button.

After selecting wireless connection in Settings menu, the

icon will be displayed dynamically.

The icon is always on to indicate successful pairing with

mobile APP.

The icon disappears to indicate mobile APP pairing

failure, or the product is unpaired.

Smart Mode. The product will adjust the fan speed

according to the internal detected temperature to ensure

that it is in optimal working condition.
Quiet Mode. The fan keeps running at low speed for

minimum noise, and the brightness should be kept below

80% in case of overheating protection.

Status Icon Description

① APP Connection Status Icon

② Fan Status Icon

None grouping status. The product defaults to the factory

status, and will not be affected by other groups.

If the icon is always on, it means that Repeater function

is turned on, and if the icon disappears, it means the

function is turned off.

If the icon flashes, it means that the internal temperature

of the product is too high, and cooling measures need

to be taken. If the icon disappears, it means that the

operation is normal.

③ Group Status Icon

④ Repeater Status Icon

⑤ Product Overheated Alarm Icon

A stands for Group A. There are 15 groups (A~O). T

stands for Tx.

A stands for Group A. There are 15 groups (A~O). R

stands for Rx.

A stands for Group A. There are 15 groups (A~O). TR

stands for TxRx.

Brightness

Color

Temperature

Roll the wheel upwards

or downwards to adjust

brightness within

0%~100%
Press down the wheel to

quickly switch the preset

brightness, 0%, 25%, 50%,

75%, and 100%

Roll the wheel upwards or downwards to adjust color temperature within

2700K~6500K
Press down the wheel to quickly switch the preset color temperature,

2700K, 3200K, 4000K, 5600K, and 6500K

CCT Mode (Short press CCT Mode Button to enter)

Brightness Control Wheel

Color Temperature Control Wheel

Rolling the wheel will enlarge the current setting parameter value, and

it will automatically return to the main screen after 1.5 seconds of no

operation

Brightness

Rate

Special

Effect

Color

Temperature

Roll the wheel upwards

or downwards to adjust

brightness within

0%~100%
Press down the wheel to

quickly switch the preset

brightness, 0%, 25%, 50%,

75%, and 100%

Roll the wheel upwards

or downwards to adjust

color temperature within

2700K~6500K
Press down the wheel to

quickly switch the preset

color temperature, 2700K,

3200K, 4000K, 5600K, and

6500K

Short press to switch the effect,

Lv.1~Lv.5, and Lv.5 for the fast.

Press to switch light effect:

Fire → CCT Chase →

Pulsing

TV

Explosion

Faulty Bulb

Welding

→ Strobe →

Lightning

→ SOS

EFF Mode (Short press EFF Mode Button to enter)

Brightness Control Wheel

Color Temperature Control

Wheel

Light Effect Frequency (RATE) Button

Light Effect Mode (EFF) Button

② Align the reflector with the adapter ring and insert it. The ejector pin is

pinched by reflector. Rotate the reflector tightly clockwise and the ejector pin

springs back.

When disassembling, push the ejector pin and rotate the reflector

anticlockwise.

Advertising