Husqvarna 1130SBE - Manual (Page 21)

21
KEY PART
NO. NO. DESCRIPTION
4 532 19 10-79 Pulley, Impeller
5 532 18 89-09 Bearing Assembly, Flange
6 532 15 53-77 Nut, Hex Flange 5/16-18
7 532 18 03-55 Bolt, Flat Head, Carriage
5/16-18 x 5/8
8 872 27 05-05 Bolt, Carriage 5/16-1 8 x 5/8
9 532 16 31-83 Bolt
10 532 40 77-21 Housing, Auger
11 532 41 62-70 Bar, Scraper
12 532 18 40-95 Bracket, Corner Discharge
13 532 17 53-22 Base, Discharge Chute
14 810 04 05-00 Washer, Lock 5/16
15 819 11 15-07 Washer, Flat
16 874 94 05-16 Screw, Hex Head 5/16-18 x 3/4
17 532 40 56-37 Grease Fitting
18 532 17 95-82 Screw, Hex Head 5/16 x 1
19 873 80 04-00 Nut, Hex Lock 1/4-20
20 532 15 53-77 Nut, Hex Lock 5/16-18
21 532 40 13-47 Washer, Flat 5/16
22 532 40 78-34 Skid Plate, Heavy Duty
24 532 12 86-38 Wing Nut
25 872 27 05-06 Bolt, Shoulder 1/4-20
26 532 18 81-70 Retainer, Plastic
27 532 17 46-97 Washer, Thrust, 1"
28 532 19 86-36 Bolt, Shear
29 532 40 78-34 Skid Plate, Heavy Duty
30 532 40 77-22 Auger Assembly, RH
REPAIR PARTS
AUGER HOUSING / IMPELLER ASSEMBLY
SNOW THROWER - MODEL NO. 1130SBE (96193001704), PRODUCT NO. 961 93 00-17
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
KEY PART
NO. NO. DESCRIPTION
31 532 40 77-23 Auger Assembly, LH
32 532 40 77-68 O-Ring
33 532 40 77-69 Bushing, Flange 3/4
34 532 17 46-81 Washer, Thrust 3/4
35 532 17 46-84 Bearing, Thrust 3/4
36 532 40 77-57 Shaft, Impeller
37 532 17 46-83 Washer, Thrust 5/8
38 532 40 77-58 Bushing, Flange 5/8
39 532 40 77-67 Screw, Hex Head 5/16-18 x 3/4
40 532 40 77-60 Plug, Case
41 532 40 77-61 Housing, Gearbox, RH
42 532 40 77-70 Seal, Oil
43 532 40 77-62 Bushing, Flange, 1"
44 532 18 92-82 Key, Square 1/4 x 1/4 x 7/8
45 532 40 77-63 Gear, Worm
46 532 40 77-64 Shaft, Auger
47 532 40 77-65 Housing, Gearbox, LH
48 532 18 41-05 Impeller Assembly
49 874 78 04-26 Screw, Hex Head 1/4-20 x 1-5/8
50 532 40 77-66 Gasket, Gearbox
51 532 18 42-05 Pin, Roll 3/16 x 1-1/8
52 532 18 47-47 Bar, Drift Cutter
53 872 27 05-06 Bolt
54 532 19 87-09 Stop
55 532 19 86-38 Spacer
56 532 18 06-84 Multi-Wrench
57 532 19 67-10 Gearbox Assembly
58 532 18 79-25 Bearing