Husqvarna 125E User Manual
Page 2
2
CONTENTS
Contents
CONTENTS
Contents
2
. . . . . . . . . . . . . . . . . . . . . . . .
Note the following before starting
2
. . . .
KEY TO SYMBOLS
Symbols
3
. . . . . . . . . . . . . . . . . . . . . . . . .
SAFETY INSTRUCTIONS
Personal protective equipment
4
. . . . . .
Machine’s safety equipment
4
. . . . . . . .
Cutting equipment
5
. . . . . . . . . . . . . . . . .
Checking, maintaining and servicing
the machine’s safety equipment
5
. . . . .
General safety precautions
8
. . . . . . . . .
Starting
9
. . . . . . . . . . . . . . . . . . . . . . . . .
Fuel safety
9
. . . . . . . . . . . . . . . . . . . . . . .
Transporting and storage
9
. . . . . . . . . . .
General working instructions
9
. . . . . . . .
Basic safety rules
9
. . . . . . . . . . . . . . . . .
Basic working techniques
10
. . . . . . . . . .
KNOW YOUR EDGER
Know your edger
12
. . . . . . . . . . . . . . . . . .
ASSEMBLY
Assembling the loop handle
13
. . . . . . . . .
Assembling the blade
13
. . . . . . . . . . . . . .
FUEL HANDLING
Fuel
14
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fueling
14
. . . . . . . . . . . . . . . . . . . . . . . . . .
STARTING AND STOPPING
Check before starting
15
. . . . . . . . . . . . . .
Starting and stopping
15
. . . . . . . . . . . . . .
MAINTENANCE
Carburetor
17
. . . . . . . . . . . . . . . . . . . . . . .
Muffler
17
. . . . . . . . . . . . . . . . . . . . . . . . . .
Spark plug
18
. . . . . . . . . . . . . . . . . . . . . . .
Air filter
18
. . . . . . . . . . . . . . . . . . . . . . . . . .
Bevel gear
18
. . . . . . . . . . . . . . . . . . . . . . .
Adjusting the edger’s cutting depth
19
Maintenance schedule
19
. . . . . . . . . . . . .
TECHNICAL DATA
Technical data
20
. . . . . . . . . . . . . . . . . . . .
WARRANTY STATEMENT
21
. . . . . . . . .
EMISSION CONTROL
WARRANTY STATEMENT
22
. . . . . . . . .
Note the following before
starting:
Husqvarna AB has a policy of continuous
product development and therefore
reserves the right to modify the design and
appearance of products without prior
notice. Long--term exposure to noise can
result in permanent hearing impairment.
Always use approved hearing protection.
Maintenance, replacement, or repair of the
emission control devices and system may
be performed by any nonroad engine re-
pair establishment or individual.
The Emissions Compliance Period referred
to on the Emissions Compliance label indi-
cates the number of operating hours for
which the engine has been shown to meet
Federal emissions requirements.
Category C = 50 hours, B= 125 hours, and
A = 300 hours.
For reference, please fill out the following
information that will be needed for future
servicing of your trimmer:
Model Number:
Serial Number:
Purchase Date:
Purchased From:
WARNING:
An edger can be
dangerous if used incorrectly or
carelessly, and can cause serious
or fatal injury to the operator or
others. It is extremely important
that you read and understand the
contents of this operator’s manual.
WARNING:
Under no circum-
stances may the design of the
machine be modified without the
permission of the manufacturer.
Always use genuine accessories.
Non--authorized modifications
and/or accessories can result
in serious personal injury or the
death of the operator or others.
Your warranty may not cover
damage or liability caused by the
use of non--authorized accesso-
ries or replacement parts.