Harman-Kardon AVR 330 - Manual (Page 31)

ADVANCED FEATURES
ADVANCED FEATURES 31
The AVR 330 is equipped with a number of advanced
features that add extra flexibility to the unit’s operation.
While it is not necessary to use these features to
operate the unit, they provide additional options that
you may wish to use.
Surround Amplifier Channel Assignment
The AVR 330 is equipped with seven full-power
amplifier channels to allow for complete 7.1-channel
operation without the need for additional external
amplifiers. However, in some installations you may wish
to use the traditional 5.1-channel configuration for the
main listening room, which allows the surround back
left/right amplifier channels to be used to power
speakers placed in a remote zone location.
If you wish to use the Surround Back channel ampli-
fiers to power the remote zone, you must change a
setting in the
ADVANCED SELECT menu.
To make that change, first call up the menu system
by pressing the OSD Button
v to bring the
MASTER MENU (Figure 1) to the screen. Next,
press the
¤ Button n until the > cursor is next to
the ADVANCED line. Press the Set Button p
to enter the ADVANCED SELECT menu
(Figure 10).
Figure 10
To change the setting so that the Surround Back
amplifiers are fed by the source selected through
the Multiroom system, press the
‹ / › Buttons o
so that MR SP appears; then press the Set
Button p.
Remember that once this setting is made, you will not
be able to take advantage of any of the 6.1/7.1-
channel decoding or processing modes, and that the
speakers used for the remote zone must be connected
to the Surround Back/Multiroom Speaker Outputs
‚. The volume for these speakers is set by the
multiroom system, as explained on page 33 of
this manual.
Once this setting is made, you may press the ¤
Button n to make any of the other adjustments
available on this menu. If no other adjustments are
needed, press the OSD Button
v to exit the
menu system.
Display Brightness
The AVR 330’s front-panel displays are set at a default
brightness level that is sufficient for viewing in a nor-
mally lit room. However, in some home theater instal-
lations, you may wish to occasionally lower the bright-
ness of the display, or turn it off completely. To change
the display brightness setting for a specific listening
session, you will need to make an adjustment in the
ADVANCED SELECT menu. To start the
adjustment, press the OSD Button
v to bring the
MASTER MENU to the screen. Press the ¤
Button n, until the on-screen > cursor is next to
the ADVANCED line. Press the Set Button p
to enter the ADVANCED SELECT menu
(Figure 10).
To change the brightness setting, at the ADVANCED
SELECT menu, make certain that the on-screen
> cursor is next to the VFD line, and press the ›
Button o until the desired brightness level is shown
in the video display. When FULL is highlighted, the
display is at its normal brightness. When HALF is
shown, the display is at half the normal brightness
level. When OFF is shown, all of the front-panel
indicators will go dark. However, the Power Indicator
3 will always remain lit to remind you that the unit is
turned on.
Once the desired brightness level is selected, it will
remain in effect until it is changed again or until the
unit is turned off.
If you wish to make other adjustments, press the
⁄ / ¤ Buttons n until the on-screen > cursor is
next to the desired setting or the BACK TO
MASTER MENU line and press the Set Button
p. If you have no other adjustments to make, press
the OSD Button
v to exit the menu system.
Turn-On Volume Level
As is the case with most audio/video receivers, when
the AVR 330 is turned on, it will always return to the
volume setting in effect when the unit was turned off.
However, you may prefer to always have the AVR 330
turn on at a specific setting, regardless of what was
last in use when the unit was turned off. To change
the default condition so that the same volume level
is always used at turn-on, you will need to make an
adjustment in the ADVANCED SELECT
menu. To start the adjustment, press the OSD Button
v to bring the MASTER MENU (Figure 1)
to the screen. Press the
¤ Button n, until the on-
screen › cursor is next to the ADVANCED line.
Press the Set Button p to enter the ADVANCED
SELECT menu (Figure 10).
At the ADVANCED SELECT menu, make
certain that the on-screen
> cursor is next to the
VOLUME DEFAULT line by pressing the
⁄ / ¤ Buttons n as needed. Next, press the ›
Button o so that the word ON is shown in
the video display. Next, press the ¤ Button n
once so that the on-screen > cursor is next to the
DEFAULT VOL SET line. To set the desired
turn-on volume, press the
‹ / › Buttons o until the
desired volume level is shown on the DEFAULT
VOL SET line. This setting may NOT be made
with the regular volume controls.
NOTE: Since the setting for the turn-on volume can-
not be heard while the setting is being made, you may
wish to determine the setting before making the
adjustment. To do this, listen to any source and adjust
the volume to the desired level using the regular
Volume Controls
Щ о. When the desired
volume level to be used at turn-on is reached, make a
note of the setting as it appears in the lower third of
the video screen or in the Lower Display Line
¯.
(A typical volume level will appear as a negative num-
ber such as –25dB.) When making the adjustment,
use the
‹ / › Buttons o to enter this setting.
Unlike some of the other adjustments in this menu, the
turn-on volume default will remain in effect until it is
changed or turned off in this menu, even when the
unit is turned off.
If you wish to make other adjustments, press the
⁄ / ¤ Buttons n until the on-screen > cursor is
next to the desired setting or the BACK TO
MASTER MENU line and press the Set Button
p. If you have no other adjustments to make, press
the OSD Button
v to exit the menu system.
Semi-OSD Settings
The semi-OSD system places one-line messages at
the lower third of the video display screen whenever
the volume, input source, surround mode, tuner
frequency or any of the configuration settings are
changed. The semi-OSD system is helpful in that it
provides feedback on any control changes or remote
commands using the video display when it is difficult
to view the front-panel displays. However, you may
occasionally prefer to turn these displays off for a par-
ticular listening session. You may also want to adjust
the length of time the displays remain on the screen.
Both of those options are possible with the AVR 330.
38
* A D V A N C E D S E L E C T *
S B A M P S : S B S P
V F D : F U L L
V O L U M E D E F A U L T : O F F
D E F A U L T V O L S E T : 2 5 d B
S E M I O S D : O F F O N
S E M I O S D T I M E O U T : 2
F U L L O S D T I M E O U T : 2 0
B A C K T O M A S T E R M E N U
>