Hotpoint LI2JBA - Manual (Page 7)

Consult the designs in the front pages referenced in the text by alphabet
letters. Closely follow the instructions set out in this manual. All
responsibility, for any eventual inconveniences, damages or fires caused
by not complying with the instructions in this manual, is declined.
Installation
The cooker hood must be placed at a minimum distance of 60 cm from
the cooking plane for electric cookers and 70cm for gas or mixed
cookers. The hood can be installed above these heights but for
optimum performance it should be installed at the distance quoted for
the appropriate heat source.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only.
Do not fix chimney flue to furniture or fly over shelves unless the
chimney flue can be easily removed, in case maintenance is ever
required.
Use
The cooker hood is provided with an upper air exit B for discharging
fumes externally for models including chimney flue C ( Suction
Version A- exhaust pipe 13A not supplied).
In the instance where it is not possible to discharge cooking fumes and
vapours externally even if utilising the model with chimney flue C, the
cooker hood may be used in the filter version F by mounting two
active carbon filters E, the fumes and vapours are then recycled via
the upper grill G (depending on the model the grill may be directly
placed on the chimney flue or via the mounting of two small grills –
16F).
If in possession of a model with grill placed on chimney flue then two
H extensions must be placed on the deflector 13F.
The models provided with small dome D may only be used in the filter
version F.
The models without suction motor and the models with electric valve
only function in the suction version and must be connected to a
peripheral suction unit (not supplied).
Electrical connection
The electrical tension must correspond to the tension noted on the
label placed inside the cooker hood. Connect the electrical plug,
where provided, to the an easily accessible outlet in conformity with
local standards in force.
Where an electrical plug is not provided (for direct connection to
electrical network) place a standards approved bipolar switch with an
aperture distance of not less than 3mm (accessible) from the contacts.
Operation
The cooker hood is provided with a key or pushbutton control panel
situated of the frontal part of the cooker hood, depending on the basis
of the cooker hood type in possession. For proper operation consult
the text below and the relative illustration:
a. ON/OFF lighting
b. OFF motors/Valve
c. - d. - e. Minimum suction power/ON Valve (c.), medium (d.),
maximum (e.).
f. Operation warning light (where present).
Use the high suction speed in cases of concentrated kitchen vapours.
It is recommended that the cooker hood suction is switched on for 5
minutes prior to cooking and to leave in operation during cooking and
for another 15 minutes approximately after terminating cooking.
Only in the case of models with electric valve:
In this case the hood is provided with a control panel placed on the
front part of the hood with two keys, one for turning the lamp on and
off and one for opening and closing the valve.
Attention: opening and closing the valve is never immediate and takes
place after a brief lapse of time.
Model with electronic controls
1-Motor OFF button
2- ON button and motor speed selection button 1 - 2 - 3 - 1 - 2 - .
. . .
3-Speed 1 LED
4-Speed 2 LED and metal grease filter saturation LED (in this latter
case, the LED will flash - See instructions on grease filter
cleaning).
5-Speed 3 LED and active carbon filter saturation LED (in this
latter case, the LED will flash - See instructions on active carbon
filter replacement).
Warning!
The active carbon filter saturation LED is not activated.
In order to activate the active carbon filter saturation indicator,
press buttons 2 and 7 simultaneously for 3 seconds. Initially,
only LED 4 will flash, then after the 3 seconds have passed, LED
5 will also start flashing, indicating that the active carbon filter
saturation control system is active.
To switch off the system, re-press the same two buttons: after
3 seconds LED 5 will stop flashing and the device will be
INSTRUCTION ON MOUNTING AND USE GB
a
a b-c d e f
b-c-d-e b-c-d-e a
a b c d e
1 2 3 4 5 6 7
8 9