Horizon Fitness T901 - Manual (Page 8)

1
INTR
ODUC
TION
IMPOR
TANT
PRE
CA
UTIONS
BEF
ORE
YOU
BE
GIN
TREADMILL OPER
ATION
LIMITED
W
ARR
ANTY
TR
OUBLE
SHOO
TING
&
MAINTENANCE
CONDITIONING
GUIDELINE
S
AS
SEMBL
Y
BEF
ORE
YOU
BE
GIN
AS
SEMBL
Y
1
INTR
ODUC
TION
IMPOR
TANT
PRE
CA
UTIONS
TREADMILL OPER
ATION
CONDITIONING GUIDELINE
S
TR
OUBLE
SHOO
TING
&
MAINTENANCE
LIMITED
W
ARR
ANTY
YOU’RE FINISHED!
NEVER USE THE TREADMILL WITHOUT SECURING THE SAFETY KEY CLIP TO
YOUR CLOTHING. PULL ON THE SAFETY KEY CLIP FIRST TO MAKE SURE IT
WILL NOT COME OFF YOUR CLOTHING.
BEFORE YOU BEGIN
Congratulations on choosing your treadmill! You’ve taken an important step in developing and sustaining
an exercise program! Your treadmill is a tremendously effective tool for achieving your personal fitness
goals. Regular use of your treadmill can improve the quality of your life in so many ways.
HERE ARE JUST A FEW OF THE HEALTH BENEFITS OF ExERCISE:
• Weight Loss
• A Healthier Heart
• Improved Muscle Tone
• Increased Daily Energy Levels
The key to reaping these benefits is to develop an exercise habit. Your new treadmill will help you eliminate
obstacles that prevent you from exercising. Inclement weather and darkness won't interfere with your
workout when you use your treadmill in the comfort of your home. This guide provides you with basic
information for using and enjoying your new machine.
LOCATION OF THE TREADMILL
Place the treadmill on a level surface. There should be 6 feet of
clearance behind the treadmill, 3 feet on each side and one foot in
front for folding and the power cord. Do not place the treadmill in any
area that will block any vent or air openings. The treadmill should not
be located in a garage, covered patio, near water or outdoors.
SAFETY KEY
Your treadmill will not start unless the safety key is placed in position. Attach the clip end securely to
your clothing. This safety key is designed to cut the power to the treadmill if you should fall. Check the
operation of the safety key every 2 weeks.
WARNING
3 feet
6 feet
3 feet
1 foot
DO NOT STAND ON THE BELT
While you are preparing to use the
treadmill, do not stand on the belt. Place
your feet on the side rails before starting
the treadmill. Start walking on the belt
only after the belt has begun to move.
Never start the treadmill at a fast running
speed and attempt to jump on!
WARNING
ASSEMBLY STEP 
FLAT WASHERS (L)
SPRING WASHERS (M)
BOLTS (H)
CONSOLE MAST
SUPPORT BAR
SUPPORT
BAR BRACKET
FLAT WASHER (L)
8 mm
Qty: 6 SPRING WASHER (M)
8 mm
Qty: 6 BOLT (H)
25 mm
Qty: 6
HARDWARE BAG  CONTENTS:
Open HARDWARE BAG .
Align SUPPORT BAR with holes in
CONSOLE MAST and SUPPORT BAR
BRACKET as shown.
Attach bottom of SUPPORT BAR to
CONSOLE MAST using 2 BOLTS (H),
2 SPRING WASHERS (M) and 2 FLAT
WASHERS (L).
* Do not tighten bolts until step F.
To attach top of SUPPORT BAR, insert
1 BOLT (H), 1 SPRING WASHER (M) and
1 FLAT WASHER (L) through SUPPORT
BAR BRACKET and SUPPORT BAR as
shown.
Repeat on other side.
IMPORTANT: Completely tighten ALL
bolts from steps 1-6.
Connect POWER PLUG to the treadmill
and connect the cord to a power outlet.
The POWER SWITCH is located next to
the POWER CORD. Flip this switch to the
'ON' position, so that the switch is lit.
You will hear a beep and the console will
light up.
Before the first use, lubricate the
treadmill deck by following the
instructions in the Maintenance section.
A
B
C
D
E
F
G
H
CONSOLE MAST
SUPPORT BAR
SUPPORT BAR BRACKET
FLAT WASHER (L)
SPRING WASHER (M)
BOLT (H)
POWER SWITCH CIRCUIT BREAKER
POWER PLUG
T901_Rev.2.0.indd 14-15 9/10/08 11:15:51 AM