Husqvarna 96045001700 User Manual
Page 33
33
TRACTOR - MODEL NO. LGT2554 (96045001700), PRODUCT NO. 960 45 00-17
CHASSIS
KEY PART
NO. NO.
DESCRIPTION
5
532 40 87-01 Dash
14
532 41 10-46 Hood Asm.
15
532 19 89-07 Lens LH
18
532 40 86-07 Grille Asm.
25
532 19 89-06 Lens RH
34
532 19 61-25 Plate Engine
36
817 06 05-12 Screw 5/16-18 x 3/4
37
532 40 18-25 Fender
52
873 68 05-00 Nut Crown Lock 5/16-18
58
532 19 43-14 Bracket Fender
68
817 49 05-08 Screw 5/16-18 x 1/2
130 532 41 63-58 Screw #10 x .750 BOS Thread
137 532 40 75-90 Bumper Dash
150 532 19 85-12 Duct Heat Hood
152 532 19 95-35 Shield Browning/Debris
159 817 00 06-12 Screw 3/8-16 x 3/4
161 532 40 18-26 Console Fuel Window
162 532 14 24-32 Screw Hex Wsh Hi-Lo 1/4 x 1/2
165 532 19 68-26 Bracket Support Tank
175 532 19 63-04 Crossmember
176 532 40 07-76 Screw 10-24 x 5/8
177 532 19 52-27 Bushing Steering
178 532 19 97-82 Cargo Asm. Net
180 532 19 54-77 Chassis
181 532 40 30-25 Bushing Mtg. Fender Crgo.
182 532 40 68-59 Dash Lower
183 874 78 05-20 Bolt Fin Hex 5/16-18 unc x 1-1/4
189 817 00 05-12 Screw 5/16-18 x 3/4
194 873 90 05-00 Nut Lock Hex Flange 5/16-18
196 532 40 02-99 Console Asm. Deck Lift
KEY PART
NO. NO.
DESCRIPTION
199 532 19 82-59 Plate Deck Lift
202 532 40 30-48 Vent Side Hood RH
203 532 40 30-76 Vent Side Hood LH
204 532 41 66-13 Vent Asm Hood Top
205 532 40 17-09 Skirt Hood Side RH
206 532 40 17-11 Skirt Hood Side LH
207 532 19 71-98 Bezel RH
208 532 19 71-99 Bezel LH
209 532 19 91-30 Insert Hex Top RH
210 532 19 91-31 Insert Hex Top LH
211 532 19 91-32 Insert Hex Bottom RH
212 532 19 91-33 Insert Hex Bottom LH
213 874 76 05-12 Bolt Hex Hd 5/16-18 unc x 3/4
214 532 19 91-45 Clip Retainer
217 532 40 91-67 Rod Pivot
218 532 19 63-95 Hood Stop
221 532 19 89-09 Reflector LH
228 532 19 51-61 Stud Fastener
234 532 40 47-42 Bumper Hood
235 532 40 61-29 Spacer Fender
236 873 93 05-00 Nut Center Lock 5/16-18 unc
289 532 40 35-71 Plug Cruise/Phone
296 532 40 86-06 Trim
298 532 11 04-52 Nut Push
299 532 40 50-12 Logo
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm