Hotpoint DE47X1 - Manual (Page 13)

GB
13
Note: If your appliance has two ovens: When the
timer has been set for one oven it is possible to
use the other oven only during the same
Automatic programme.
At the end of the Automatic
Cook Period the Auto Symbol
will flash and an intermittent
bleeping sound will be heard.
The audible tone will continue
unless cancelled.
The 'Auto' symbol will continue to flash until the
timer is returned to Manual operation (see below).
Step 8 Press the Manual
button, the audible tone will be
cancelled and the oven(s) will be
returned to Manual.
Step 9 Turn the oven control(s) to the OFF position.
Note 1 When cooking automatically the Cook Period
can be checked at any time by simply pressing
the Cook Period button.
Note 2 When cooking automatically the End Time can
be checked at any time by simply pressing
the End Time button.
b) TO SET TIMER TO SWITCH ON
IMMEDIATELY AND OFF AUTOMATICALLY
AFTER A SET COOK PERIOD
Step 1 Check that the correct time of day is set, if
not follow instructions for setting the time
of day.
Step 2 Place food onto the correct shelf position
in the oven and close the oven door(s).
Step 3 Turn the oven control(s) to the required tem-
perature, and if necessary select the
appropriate oven function.
Step 4 Press & hold in the
Cook Period button, the display
will read 0.00 and the 'cookpot'
symbol will light up.
With the Cook Period button still
held in set the required Cook
Period using the "+" and "-"
buttons. Example: 1hr 30
minutes (as shown).
Step 5 Release all buttons.
The timer display will revert to
the time of day with the 'Auto'
symbol lit & 'cookpot' symbol
remaining lit.
At the end of the Cook Period
the 'Auto' symbol will flash and
an intermittent audible tone will
be heard. The audible tone will
continue until cancelled. The
'Auto' symbol will continue to
flash until the timer is returned to
Manual operation (see below).
Step 6
Press the Manual
button. The audible tone will be
cancelled and the oven(s) will be
returned to Manual.
Step 7 Turn the oven control(s) to the OFF position.
TO CANCEL AN AUTO COOKING
PROGRAMME BEFORE THE COOK
PERIOD HAS FINISHED.
Step 1 Turn the oven control to the OFF position.
Step 2 Press the Manual
button to return the oven to
"Manual" operation. The 'Auto'
symbol will go out.
Note 1 When cooking automatically the Cook
Period can be checked at any time by simply
pressing the Cook Period button.
OTHER NOTES ON TIMER OPERATION
1. When cooking Automatically the Cook Period can
be checked at any time simply by pressing the
Cook Period button.
2. When cooking Automatically the End Time can be
checked at any time by simply pressing the End
Time button.
3. Having set a Cook Period and End Time an
electronic device stores the information. The device
within the timer will switch the oven(s) on and off at
the required times.
4. When setting an Auto Cooking Programme and a
mistake is made, to clear:-
(a) Press & release the Manual button.
(b) Start the sequence again.
5. If at any time the display shows three flashing zero's
0.00 and 'Auto', it is likely that the electricity supply
to the oven has been interrupted. Reset the timer
to the correct time of day. Food in the oven may,
therefore, not have been cooked, before serving
check food is thoroughly heated and completely
cooked.
6. To set each function always press and hold the
required function button and at the same time press
"+" or "-" buttons.
A
U
T
O 6 1 2 0
.
6 1 2 0
.
1 3 0
.
A
U
T
O 4 1 2 0
.
A
U
T
O 6 1 2 0
.
NOTE: The Cookpot symbol disappears
6 1 2 0
.
5 1 0 0
.