Grizzly G8994z User Manual
Page 4
G8994Z Variable Speed Jig Saw
-2
-
10. USE PROPER EXTENSION CORD
for the charger. Make sure your
extension cord is in good condition.
Conductor size should be in accor-
dance with the chart below. The
amperage rating should be listed on
the motor or tool nameplate. An
undersized cord will cause a drop in
line voltage resulting in loss of power
and overheating. Your extension
cord must also contain a ground wire
and plug pin. Always repair or
replace extension cords if they
become damaged.
Minimum Gauge for Extension Cords
11. WEAR PROPER APPAREL.
Do not
wear loose clothing, gloves, neck-
ties, rings, bracelets, or other jewel-
ry which may get caught in moving
parts. Non-slip footwear is recom-
mended. Wear protective hair cover-
ing to contain long hair.
12. ALWAYS USE SAFETY GLASSES.
Also use face or dust mask if cutting
operation is dusty. Everyday eye-
glasses only have impact resistant
lenses, they are NOT safety glass-
es.
13. SECURE WORK.
Use clamps or a
vise to hold work when practical. It’s
safer than using your hand and frees
both hands to operate tool.
14. DON’T OVERREACH.
Keep proper
footing and balance at all times.
S
Sa
affe
etty
y IIn
ns
sttrru
uc
cttiio
on
ns
s F
Fo
orr P
Po
ow
we
err T
To
oo
olls
s
A
AM
MP
P
L
LE
EN
NG
GT
TH
H
R
RA
AT
TIIN
NG
G 2
25
5fftt
5
50
0fftt 1
10
00
0fftt
0-6
18
16
16
7-10
18
16
14
11-12
16
16
14
13-16
14
12
12
17-20
12
12
10
21-30
10
10
No
1
15
5.. M
MA
AIIN
NT
TA
AIIN
N T
TO
OO
OL
LS
S W
WIIT
TH
H C
CA
AR
RE
E..
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
16. DISCONNECT TOOLS
before ser-
vicing and changing accessories,
such as blades, bits, cutters, and
the like.
1
17
7.. R
RE
ED
DU
UC
CE
E T
TH
HE
E R
RIIS
SK
K O
OF
F U
UN
NIIN
NT
TE
EN
N--
T
TIIO
ON
NA
AL
L S
ST
TA
AR
RT
TIIN
NG
G.. Make sure
switch is in off position before plug-
ging in.
1
18
8.. U
US
SE
E R
RE
EC
CO
OM
MM
ME
EN
ND
DE
ED
D A
AC
CC
CE
ES
S--
S
SO
OR
RIIE
ES
S.. Consult the owner’s man-
ual for recommended accessories.
The use of improper accessories
may cause risk of injury.
19. CHECK DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate proper-
ly and perform its intended function.
Check for alignment of moving
parts, binding of moving parts,
breakage of parts, mounting, and
any other conditions that may affect
its operation. A guard or other part
that is damaged should be properly
repaired or replaced.
19. NEVER LEAVE TOOL RUNNING
UNATTENDED.
Turn the power off,
and don’t leave tool until it comes to
a complete stop.
20. NEVER ALLOW UNTRAINED
USERS TO RUN THIS TOOL
WHILE UNSUPERVISED.
21. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING THE TOOL.
Seek formal
training or research books or maga-
zines that specialize in power tools.