Grizzly G9717 - Manual (Page 9)

G9717 6" Grinder -8-
O Op pe erra attiio on n o off tth hiis s e eq qu uiip pm me en ntt h ha as s tth he e p po otte en nttiia all
tto o p prro op pe ell d de eb brriis s iin ntto o tth he e a aiirr w wh hiic ch h c ca an n c ca au us se e
e ey ye e iin njju urry y.. A Allw wa ay ys s w we ea arr s sa affe etty y g glla as ss se es s o orr g go og g--
g glle es s w wh he en n o op pe erra attiin ng g e eq qu uiip pm me en ntt.. E Ev ve erry yd da ay y
g glla as ss se es s o orr rre ea ad diin ng g g glla as ss se es s o on nlly y h ha av ve e iim mp pa ac ctt
rre es siis stta an ntt lle en ns se es s,, tth he ey y a arre e n no ott s sa affe etty y g glla as ss se es s..
B Be e c ce errtta aiin n tth he e s sa affe etty y g glla as ss se es s y yo ou u w we ea arr m me ee ett
tth he e a ap pp prro op prriia atte e s stta an nd da arrd ds s o off tth he e A Am me erriic ca an n
N Na attiio on na all S Stta an nd da arrd ds s IIn ns sttiittu utte e ((A AN NS SII))..
D DO O N NO OT T m ma ak ke e a ad djju us sttm me en ntts s w wh hiille e tth he e g grriin nd de err iis s
rru un nn niin ng g.. E En ns su urre e tth ha att tth he e s sw wiittc ch h iis s o offff,, p po ow we err iis s
d diis sc co on nn ne ec ctte ed d a an nd d m mo ov viin ng g p pa arrtts s h ha av ve e s stto op pp pe ed d
b be effo orre e m ma ak kiin ng g a ad djju us sttm me en ntts s.. F Fa aiillu urre e tto o c co om mp plly y
c co ou ulld d rre es su ulltt iin n s se erriio ou us s iin njju urry y o orr e elle ec cttrriic ca all s sh ho oc ck k
h ha az za arrd d..
S SE EC CT TIIO ON N 5 5:: O OP PE ER RA AT TIIO ON NS S
S Stta arrttiin ng g a an nd d S Stto op pp piin ng g
Once assembly has been completed, the G9717
Grinder is ready for use in the shop.
The switch is located on the front of the grinder.
To turn the grinder “ON”, push the right hand side
of the rocker switch, to turn it “OFF”, push the left
hand side of the switch. Always make sure the
wheels come up to full speed before introducing
the workpiece to the wheel.
When mounting a new wheel, or when there is
any concern about wheel integrity, stand away
from the line of rotation of the wheel and then turn
the wheel “ON”. If there is a potential problem it
will generally occur when the wheel is first start-
ed.
Aluminum oxide and silicon carbide wheels are
marked in a somewhat uniform manner by all the
major manufacturers. Understanding these mark-
ings will help you understand the capabilities of
various wheels. Always refer to the manufactur-
er’s grinding recommendations when selecting a
wheel for your project.
The basic format for wheel numbering is:
P Prre effiix x A Ab brra as siiv ve e G Grriitt G Grra ad de e B Bo on nd d
T Ty yp pe e S Siiz ze e T Ty yp pe e
3 36 6 A A 6 60 0 L L V V
The most common abrasive types used are A for
Aluminum Oxide and C for Silicon Carbide, and
occasionally SG for seeded gel. The prefix is the
manufacturer’s designation for a particular type.
The grit size is a number referring to the size of
the abrasive grain in the wheel. The lower the
number the coarser the wheel - 10 is a very
coarse wheel for roughing and 220 is usually the
upper range for fine finish work.
Grade is an indication of the hardness of the
wheel, with A being softest to Z the hardest.
Bond Type refers to the type of bonding material
used to hold the abrasive material. Most general
purpose wheels will have a V indicating Vitrified
clay is used, providing a high strength and good
porosity. The other most common is B for resin
where synthetic resins are used. These are used
to grind cemented carbide and ceramic materials
There may be other numbers inserted which
have meaning for a particular type of wheel.
Refer to the manufacturer’s technical data for a
complete explanation.
W Wh he ee ell S Se elle ec cttiio on n