Marantz DV9600 - Manual (Page 39)

6 DVD Setup Menu
39
English
About source audio output
When the source output mode has been switched between the 5.1 Channel and 2 Channel mode settings using
the Audio Out setting in the Setup screen Audio Setup 1 menu, audio output for each source will be as shown in
the following table.
*1 : Discs that prohibit downmixing will be output front L channel and front R channel.
*2 : Discs that prohibit downmixing also mute the digital output.
*3 : The left/right audio tracks are output when playing a CD layer.
AUDIO
CONTENTS
OUTPUT
MODE
AUDIO OUT (2 CH)
5.1 CH
2 CH
5.1 CH
2 CH
5.1 CH/
2 CH
5.1 CH
2 CH
5.1 CH/
2 CH
5.1 CH/
2 CH
DV
D
CD
Super Audio CD
Video CD
Dolby
Digital
Dolby
Digital
Karaoke
LPCM
DTS
DVD
-Audio
Front Lch, Rch
2 ch DOWNMIX Lch, Rch
2 ch DOWNMIX Lch, Rch
2 ch DOWNMIX Lch, Rch
MUTE
MUTE
Center Surround LS, RS
2 ch DOWNMIX Lch, Rch
Lch, Rch
Lch, Rch
AUDIO OUT (5.1 CH) DIGITAL OUTPUT (S/PDIF)
Lch, Rch
Front Lch, Rch
L, R (Front L,R) Center Surround L,R Sub Woofer PCM Bit Stream
Dolby Digital
Lch, Rch
DTS
*2
*1
Center Surround LS, RS LFE
LFE
MUTE
Lch, Rch
MUTE
MUTE
Dolby Digital
Lch, Rch Lch, Rch
MUTE
MUTE
2 ch DOWNMIX
Lch, Rch
5.1 CH
2 CH
Front Lch, Rch Center Surround LS, RS LFE
MUTE
2 ch DOWNMIX
Lch, Rch
*3
5.1 CH
2 CH 2 ch DOWNMIX Lch, Rch
Front Lch, Rch Center Surround LS, RS LFE
MUTE
Lch, Rch
2 ch DOWNMIX
Lch, Rch
5.1 CH/
2 CH
2 ch DOWNMIX Lch, Rch MPEG MPEG MUTE
Note
• Even if you set Audio Out to 5.1 Channel,
you’ll only get sound from all speakers when
playing a multi-channel DVD-Audio disc, multi-
channel Super Audio CD disc, Dolby Digital or
DTS encoded DVD disc.
• If you set to 2 Channel, Dolby Digital and DTS
are mixed down to two channels so you still
hear all the audio recorded on the disc.
• Some DVD-Audio discs don’t allow down-
mixing of audio. These discs always output
multi-channel audio regardless of the setting
made here.
• Sound recorded on MPEG is outputted on 2
channel even if Audio Out is set to 5.1 CH.
• This setting cannot be chosen when HDMI is
connected while either Auto or Multi PCM
selected for the HDMI audio setting. (page 54)
• Audio is not output from the audio output jacks
when i.LINK is connected. (page 55)
Audio Out
• Default setting: 2 Channel
If you connected this player to your amplifier using
the 5.1 channel analog outputs (front, surround,
center and subwoofer outs), set this to 5.1
Channel; if you connected only the stereo
outputs, set to 2 Channel.
Set this to 5.1 Channel when outputting multi-
channel audio from the i.LINK port; when output-
ting 2-channel audio, set to 2 Channel.