Pioneer Reference Series DEX-P9R - Manual (Page 13)

63
bridgeable amplifiers
active crossover networks
TS-WX205
TS-WX205
Full
Range
Speakers
TS-WX205
Bridged Mono
Sub
TS-W304F
or
TS-W254F
TS-WX20LP
x
2
L
Stereo
R
8 Ω Parallel
TS-W121SPL
TS-W305C
x
2
or
TS-W255C
x
2
Bridged Stereo
L
R
Stereo
Full
range
speakers
TS-W121SPL
or
TS-W101SPL
TS-W121SPL
x
2
or
TS-W101SPL
x
2
Stereo
L
R
L
Sub
Sub
Bridged Mono
Sub
3-Channel Mode
Stereo
Sub
Below are a few examples of how to build an in-car sound system with an amplifier and subwoofer combination. These
configurations match the capability of each subwoofer and amplifier, to maximise the potential of the system.
GM-X972 GM-X372
PRS-X340 GM-X374 PRS-X320 PRS-X220 GM-X574
GM-X572 GM-X372
TS-W101SPL
x
2
or
TS-W121SPL
x
2
Positioned between sound sources and amplifiers, Pioneer Crossover Networks are designed for extremely precise, clear
sound reproduction. There’s a choice of models, and each one offers accurate adjustment of frequency crossover points to
match the characteristics of subwoofers, midrange speakers and tweeters.
3-WAY ELECTRONIC CROSSOVER NETWORK CD-635
• Variable crossover frequency (Mid and Low: 50 Hz – 200 Hz or 500 Hz – 2 kHz, High and Mid 3 kHz –
10 kHz) • Cut-off slope: -12 dB/oct. (all ranges) • Subwoofer and High-Range Phase Switches • Subwoofer
output mode switch (Stereo/Mono) • Level Controller • Gold-plated RCA input/output terminals
2-WAY ELECTRONIC CROSSOVER NETWORK CD-625
• LPF and HPF (50 – 200 Hz) • Cut-off slope: -12 dB/oct. • Variable crossover frequency (50 Hz – 200 Hz
continuously variable) • Subwoofer Phase Switch • Variable Level Controller for subwoofer (between
-15 and +15 dB) • Subwoofer output mode switch (stereo/mono) • Gold-plated RCA input/output
terminals
2-WAY ELECTRONIC CROSSOVER NETWORK CD-615
• LPF and HPF • Cut-off frequency (HPF: 80 Hz or flat; LPF: 80 Hz) • Cut-off slope: -12 dB/oct.
• Subwoofer output • RCA input and outputs terminals • In-line Noise Filter (Signal Ground Isolator)
R
L
R
Sub
Bridged
4 x 70 W or 2 x 160 W 4 x 45 W or 2 x 100 W 2 x 200 W or 1 x 480 W 2 x 110 W or 1 x 300 W 2 x 70 W or 1 x 200 W
4 x 50 W 4 x 35 W 2 x 150 W 2 x 75 W 2 x 50 W
4 x 65 W 4 x 50 W 2 x 200 W 2 x 100 W 2 x 60 W
2 x 130 W 2 x 100 W 1 x 400 W 1 x 200 W 1 x 120 W
10 Hz – 45 kHz 10 Hz – 45 kHz 10 Hz – 50 kHz 10 Hz – 50 kHz 10 Hz – 50 kHz
0.008 0.008 0.008 0.008 0.008
97 dB 100 dB 100 dB 100 dB 100 dB
200 mV – 6.5 V 200 mV – 6.5 V 200 mV – 6.5 V 200 mV – 6.5 V 200 mV – 6.5 V
26.5 19.2 37.5 18.9 14.4
269 x 50 x 309 265 x 50 x 237 269 x 50 x 309 265 x 50 x 237 255 x 50 x 169
3.7 2.8 3.7 2.8 2
Amplifiers – Specifications GM-X574 GM-X374 GM-X972 GM-X572 GM-X372
DIN output power (DIN 45324, +B = 14.4 V)
Continuous output power (RMS)
Watts 14.4 V
(20 – 20 kHz/4 Ω)
(20 – 20 kHz/2 Ω)
(Bridged 4 Ω)
Frequency Response (Hz) (+o dB, -1 dB)
Distortion (%) (10 W/1 kHz)
S/N Ratio
High voltage input capability
Max. Current Consumption (A/4 Ω)
Chassis Size (W x H x D mm)
Unit Weight (kg)
amp/sub configuration examples
Bridged Mono
R
L