M-AUDIO Digital DJ System - Manual (Page 43)

Torq MixLab User Guide » Chapter 1
42
Torq MixLab User Guide » Chapter 8
42
Channel Volume Faders
Besides going to the PFL, the audio leaving the EQ also goes to the Channel Volume fader. This is the primary volume
control for the channel (though it is subordinate to the crossfader) which works just like a volume fader on a traditional
mixer. You can match volumes of the two tracks using the Channel Volume faders. However, some DJs prefer the
technique of leaving the Channel Volume faders fully up—you then match the volumes of the songs using the Gain
knobs. The reason for this is that you’re then free to use the Channel Volume faders for other effects such as volume
fades, cuts, and stutter effects, similar to the scratch techniques used on the Crossfader. Whichever approach you
choose is entirely up to you.
You can use the Volume slider on the X-Session Pro hardware controller to adjust the Channel Volume fader found
within Torq.
Note: You can quickly return a Channel Volume fader to full volume by holding SHIFT and clicking on the fader.
Crossfader
After the audio leaves the individual mixer channels via the Channel Volume faders, the signals enter their respective
sides of the Crossfader. The Crossfader is the large horizontal fader just below the Mixer. As you will see, its name is
very appropriate as it allows you to fade between the two channels in a motion that goes side to side across the mixer.
When the Crossfader is in its middle location, you will hear both of the mixer channels. If you move the Crossfader all
the way to the left, you will only hear the channel for the left Deck. Similarly, if you move the Crossfader all the way to
the right, you will only hear the right Deck.
The Crossfader was invented to offer DJs an easy way to fade out of one song while fading in another while only using
one hand. Indeed, it still performs this task quite well. However, since its introduction, DJs have taken this simple tool
and transformed it into a virtual razor blade that allows them to perform lightning-fast cuts, scratches, and a myriad of
other techniques.
You can use the hardware crossfader on X-Session Pro to control Torq’s on-screen crossfader. See chapter 13 to learn
more about X-Session Pro.
Note: Torq’s Crossfader has been designed to be very quick and responsive. However, if you are only using a mouse
to control Torq LE, you probably won’t be able to use the Crossfader for more than fading between songs. If you
want to use the Crossfader for cuts and scratching, we recommend you control the Crossfader using one of the real
Crossfaders found on SynchroScience controllers (such as X-Session Pro). The tactile response of the Crossfader
comprises part of the scratching technique.
< Crossfader Curve
Speaking of scratching, one of the improvements to crossfader design is an adjustable Crossfader Curve. This
refers to the rate at which the songs fade in and out as the crossfader is moved from one side to the other.
At one extreme is the Equal Power Contour, which is good for slow fades between two songs. As you move
the fader from the edge toward the center, it will slowly fade in one song. However, as it is fading in this song, it
will also start fading out the other song. The end result is that the overall volume remains the same as you fade,
even when both songs are playing at the same time.
At the other extreme of the adjustable range is the Hard Cut. This shape causes a song to fade in to full volume
almost immediately after moving the fader inward from the edge. Similarly, the other song will not begin to fade
out until the crossfader is almost all the way at the other edge. Then, right before the crossfader reaches the
edge, the other song will fade down. This is the shape preferred by scratch DJs as they can cut in a track to full
volume with very little motion of their hand. When performed quickly, you don’t even hear the volume fade up
and down—it sounds as if the sound is being abruptly cut in and out.