Magnadyne Keypad Keyless Entry System MKE-400A - Manual (Page 2)

Press Transmitter Button or
Keypad Key
Press the Transmitter Button
or Press and Hold the 1/2 Key
on the Keypad for 3 Seconds
Press the Transmitter Button
or Press and Hold the 3/4 Key
on the Keypad for 3 Seconds
Press the Button on the 3-
Button Transmitter or Press the
Button on the 4-Button
Transmitter or Press and Hold
the 5/6 Key on the Keypad for 3
Seconds
Press the and Button at
the Same time (3-Button
Transmitter Only) or Press and
Hold the 7/8 Key for 3 Seconds
Exit: Turn the ignition switch to the "ON" position, or press the "LOCK" button on the keypad or leave it for 15
seconds. The beeper will emit 3 long chirps and the onboard LED will turn off to confirm exit.
One Beep / One LED Flash
(Factory Default Setting)
Channel 3 Output = Momentary
Output
Channel 4 Output = Momentary
Output
Channel 5 Output = Momentary
Output
Button = Unlock Cargo
Door(s) Control
+ = Porch Light On/Off
Control
Two Beeps / Two LED Flashes
Channel 3 Output = Latched
Output
Channel 4 Output = Latched
Output
Channel 5 Output = Latched
Output
+ = Unlock Cargo
Door(s) Control
Button = Porch Light On/Off
Control
3
Programming
D. Reprogramming All Codes Back to Default
1. Enter the Code "7352000" on the keypad. The
beeper will emit 1 long chirp to confirm the correct
code was entered.
2. Press and hold the "LOCK" key on the keypad
for 5 seconds and until 5 beeps are heard, then
release.
3. The system will reprogram all codes back to
the default setting. The default program code is
"12345" and the default user code is "54321".
E. Changing the Program Code
(The default program code is "12345")
1. Enter the program code on the keypad. The
beeper will emit a long chirp to confirm the
correct code was entered.
2. Press and hold the "LOCK" key on the keypad
for 2 seconds and until 5 beeps are heard, then
release.
3. Enter a new 4 to 6 digit program code on the
keypad.
4. Finish by pressing the "LOCK" key on the
keypad. 1 long beep with 2 short beeps will
confirm the new program code has been stored
into memory.
Exit: If 15 seconds of inactivity occurs during
the above steps, the unit will default back to the
last successfully stored code. 3 longs beeps
confirm exit.
F. Programming the User Code
(The default user code is "54321")
Note: This mode will only retain the last 4 user
codes programmed. If the user code memory is
exceeded, the security system will start deleting
user codes from memory in chronological order.
1. Enter the program code on the keypad
("12345" is default). The beeper will emit a long
chirp to confirm the correct code was entered.
2. Enter a new 4 to 6 digit user code on the
keypad. Do not use "1234".
3. Finish by pressing the "LOCK" key on the
keypad. 1 long beep with 2 short beeps will
confirm the new user code has been stored
into memory.
4. If you have additional user codes (up to 4) that
need to be programmed, repeat steps 2 - 3 for
each new user code.
Exit: Press and hold the "LOCK" key for 1 second
or if 15 seconds of inactivity occurs during the
above steps, the unit will revert back to the last
successfully stored code. 3 longs beeps confirm
exit. The unit will revert back to the last success-
fully stored code. 3 longs beeps confirm exit.
Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door
Unlocks the Vehicle's Doors
Locks the Cargo Door(s)
Unlocks the Cargo Door(s)
Turns the Porch Light On or Off
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Operation
A. 4-Button Transmitter Operation
+
+
Transmitter Button System Function
Locks the Vehicle's Doors and
Cargo Door(s)
Unlocks the Vehicle's Doors
Unlocks the Cargo Door(s)
(Can be re-programmed to Turn the Porch Light On
or off)
Turns the Porch Light On or Off
(Can be re-programmed to Unlock the Cargo Doors)
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
Upon Vehicle's Door Unlock
Upon Vehicle's Door Unlock
B. 3-Button Transmitter Operation
4