Magnadyne Keypad Keyless Entry System MKE-400A - Manual (Page 3)

System Function
Locks the Vehicle's Doors and
Cargo Door(s)
Unlocks the Vehicle's Doors
Locks or Unlocks the Cargo Door
(Operation is Sequential)
Turns On the Porch Light or Turns Off the
Porch Light (Operation is Sequential)
Activates the Channel 3 Output
Activates the Channel 4 Output
Activates the Channel 5 Output
Turns On or Off the Beep Feature of the
Keypad
Remark
Parking Lights Flash Once
1. Parking Lights Flash Twice
2. Dome Light Turns On for 30 Seconds
3. Porch Light Turns On for 30 Seconds
Note: If vehicle is operating from the RV
battery only, the parking lights will not flash.
System must be in Unlocked Mode
System must be in Unlocked Mode
The Output is Active as long as the
Button is Held. Release and Repress
within 5 Seconds to Reactivate. After
5 Seconds, Reenter User Code to
Reactivate.
The Output is Active as long as the
Button is Held. Release and Repress
within 5 Seconds to Reactivate. After
5 Seconds, Reenter User Code to
Reactivate.
The Output is Active as Long as the
Button is Held. Release and Repress
within 5 Seconds to Reactivate. After
5 Seconds, Reenter User Code to
Reactivate.
1 Beep = Keypad Chirp is On (Default)
3 Beeps = Keypad Chirp is Off
C. Keypad Operation
Note: Turn the ignition switch to the "ON" position, or "LOCK" the vehicle's doors to turn off the dome light.
Keypad
Press the "LOCK" Key
Key in the User Code
Press and Hold the
"1/2" Key for 3 Seconds
Press and Hold the
"3/4" Key for 3 Seconds
Key in the User Code,
then Press and Hold
the "5/6" Key for 5
Seconds
Key in the User Code ,
then Press and Hold
the "7/8" Key for 5
Seconds
Key in the User Code,
then Press and Hold
the "9/0" Key for 5
Seconds
Key in the User Code,
then Press and Hold
the "LOCK" Key for 3
Seconds
5
Operation
6
Wire Descriptions
Listed in Order of Pin Position:
Blue Wire: Self polarizing cargo door lock output.
Connect this wire to the lock relay for the cargo
door(s) (200ma capacity).
Green/White Wire:
Self polarizing vehicle door unlock output. Connect
this wire to the unlock relay for the vehicle door(s)
(200ma capacity).
Black Wire: Main system ground. Connect to the
vehicle chassis.
Orange Wire: (-) channel #4 output. Output type is
programmable (200ma capacity).
Violet Wire: (-) channel #5 output. Output type is
programmable (200ma capacity).
Yellow Wire: +12 volt input supplied by switching on
the ignition key.
Red Wire: Vehicle battery + input. Connect this wire
to the (+) post of the vehicle battery. This wire will
provide a power source when the vehicle battery is
not shut off.
White Wire: (Fused) Parking light flash relay input.
Connect this wire to a (+) or (-) power source
(Depending on the parking light voltage requirement)
(Fused 15 amp capacity).
White/Black Wire: Porch light relay output. Connect
this wire to the vehicle porch light trigger circuit.
Blue/White Wire: Self-polarizing cargo door unlock
output. Connect this wire to the unlock relay for the
cargo doors (200ma capacity).
Green Wire: Self-polarizing vehicle door lock output.
Connect this wire to the lock relay for the vehicle
door(s) (200ma capacity).
Red/White: RV battery + input. Connect this wire to
the (+) post of the RV (house) battery. This wire will
provide a power source if the vehicle battery is shut
off.
Black/White Wire: (-) channel #3 output. Output
type is programmable (200ma capacity).
White/Black Wire: (Fused) Porch light relay input.
Connect this wire to a (+) or (-) power source
(Depending on the porch light voltage requirement)
(Fused 15 amp capacity).
Brown Wire: (Fused) Interior light relay input.
Connect this wire to a (+) or (-) power source
(Depending on the interior light voltage requirement)
(Fused 15 amp capacity).
Brown: Interior light relay output. Connect this wire
to the vehicle interior light trigger circuit.
White Wire: Parking/running light relay output.
Connect this wire to the vehicle parking/running light
trigger circuit.
Wire Harness Notes:
1. The cargo door lock/unlock outputs are terminated
into a mini 3-pin plug. For vehicles without an existing
door lock control relay system, use relay pack model
# ALA-DL1. This relay pack will plug directly into the
provided connector and operate up to (4) door lock
motors.
2. The vehicle door lock/unlock outputs are terminated
into mini 3-pin plug. For vehicles without an existing
door lock control relay system, use relay pack model
# ALA-DL1. This relay pack will plug directly into the
provided connector and operate up to (4) door lock
motors.