Memorex MVR4041 - Manual (Page 18)

18
RECORDING AND VIEWING THE
SAME TV PROGRAM
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the
VCR mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on and select the video input mode
on the TV.
1 Load a cassette tape with the
erase prevention tab intact.
The VCR will automatically
turn on. The clock display will
change in the counter
display.
2 Press the SPEED selector
button to select the desired
tape speed SP or SLP.
The counter and SP or SLP
will appear on the screen for
about 4 seconds.
TO WATCH A TAPE REPEATEDLY
NOTE: To cancel repeat mode, follow the above steps
1 and 2, then press the ENTER button to select
the OFF position. Press the MENU button to
return to the TV.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on, and select the video input
mode on the TV.
SLOW MOTION PLAYBACK
Press the SLOW button in the PLAYBACK mode.
Playback will proceed at 1/10th of the normal speed.
The SLOW indicator will light in the display for about 4
seconds. Press the PLAY button again to resume normal
playback.
NOTE: SLOW TRACKING AND VERTICAL LOCK
ADJUSTMENT
If noise bars appear in the picture during slow motion,
press the TRACKING/SET + or – button to reduce the
noise bars.
If the still picture jitters excessively, press the
TRACKING/SET + or – button to stabilize the still
picture.
" " will appear if you press the CALL button.
To cancel, press the CALL button again.
1 Press the MENU button.
Press the TRACKING/SET +
or – button to select the AUTO
REPEAT option.
2 Press the ENTER button to
select the ON position.
3 Press the MENU button.
If you press the PLAY button, the
tape will play over and over until
the repeat mode is canceled.
〈 +/–/ENTER/MENU 〉
MENU
CLOCK SET
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
ON OFF
NO NOISE BACKGROUND
〈 +/–/ENTER/MENU 〉
MENU
CLOCK SET
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
ON OFF
NO NOISE BACKGROUND
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR
DESIRED POINTS
When either the F.FWD or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
The CUE indicator or the REVEW indicator will light in
the display for about 4 seconds. When pressed twice,
the search picture will increase speed. Speed search
time depends upon the speed used (SP, LP or SLP)
during recording.
FRAME BY FRAME ADVANCE
Press the PAUSE/STILL button in the PLAYBACK mode.
The STILL indicator will light in the display for about 4
seconds. Press the PAUSE/STILL button again to resume
normal playback.
Press the SLOW button during STILL playback.
The still picture will advance by one frame each time
you press the button. Hold the button for continuous
frame by frame viewing.
Press the PAUSE/STILL button again to resume normal
playback.
NOTES: • A few noise bars will appear on the picture
during SPEED SEARCH and STILL.
• The audio output is muted during SPEED
SEARCH, STILL, FRAME ADVANCE and
SLOW MOTION.
• To prevent damage to the tape, special
playback is automatically changed to the
PLAYBACK mode after 5 minutes. RECORDING A TV
PROGRAM
00 : 00 : 00 SP
TO WATCH A STILL PICTURE
4E40401A E P14-19 4/1/01, 5:03 PM 18