Memorex MVR4041 - Manual (Page 22)

22
1 Press the CALL button to display the counter on the
screen. (When loading a cassette tape, the clock will
change to the counter automatically in the display.)
2 Before playback or recording, press the COUNTER
RESET button to set the counter to "00:00:00".
3 Begin playback or recording.
4 Press the STOP button when playback or recording
is finished.
5 Press the ZERO RETURN button. The tape will
rewind and automatically stop at the "00:00:00"
position.
SEPARATE AUDIO
PROGRAM (SAP)
1 Press the MENU button.
Press the TRACKING/SET +
or – button to select the SAP
option.
2 Press the ENTER button to
select the ON position.
3 Press the MENU button again.
When the VCR is turned on or a channel selection is
made, make certain "SAP" appears on the screen.
This means that the "Separate Audio Program" broad-
casting is available.
STEREO SAP SAP
OR
LISTENING TO SAP
Your VCR is fitted with an SAP broadcast system
which enables you to switch to a SEPARATE AUDIO
PROGRAM when viewing a selected channel.
This function applies only when the program is
broadcast in multi-languages through the SAP
broadcast system.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on, and select the video input
mode on the TV.
STEREO RECORDING
AND PLAYBACK
When a MTS STEREO
broadcast is received, the
STEREO will appear on the
screen and the program can
be viewed or recorded in
stereo (refer to pages 18 and
19 for recording procedures).
The Hi-Fi STEREO recording procedure is the same as
for normal recordings.
NOTE: When using a CATV system, stereo TV programs
may be transmitted over a mono cable channel.
In this case the word "STEREO" will not appear
and the sound will be in mono.
OUTPUT SELECTION
The VHS Hi-Fi audio system permits high fidelity
recording of MTS STEREO TV broadcasts.
When viewing an MTS STEREO TV program, or playing
a prerecorded VHS Hi-Fi STEREO videotape, press
AUDIO SELECT button to select that the audio be heard
through both speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO
position if the stereo broadcast or videotape audio is of
poor quality. The "R" and "L" positions allow the audio
from the Right or Left Hi-Fi channel to be heard over
both TV speakers. This button has no effect when
viewing a MONO videotape or TV program. Each time
when you press the button, OUTPUT SELECTION
display appears on the screen for several seconds.
Refer to the chart below.
OUTPUT
SELECTION
STEREO
L CH
R CH
MONO
SOUND HEARD ON BOTH
SPEAKERS
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
NOTES: • When playing back a tape that is not recorded
in Hi-Fi stereo mode, the audio will automati-
cally be monaural.
• When listening to a VHS Hi-Fi video tape or
MTS broadcast through the VHF/UHF jack
(Audio/Video cord not connected), the sound
will be monaural.
STEREO
〈 +/–/ENTER/MENU 〉
MENU
CLOCK SET
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
ON OFF
NO NOISE BACKGROUND
〈 +/–/ENTER/MENU 〉
MENU
CLOCK SET
TIMER REC SET
ON OFF
ON OFF
AUTO REPEAT
CH SET UP
SAP
LANGUAGE/IDIOMA/LANGUE
ON OFF
NO NOISE BACKGROUND
RECORDING STEREO BROADCASTS
USING ZERO RETURN
The zero return function provides a convenient
method of rapidly returning to the starting point of
recording or playback. The starting point can be
indexed for any location on the tape by pressing the
COUNTER RESET button and ZERO RETURN
button.
4E40401A E P20-25 4/1/01, 5:04 PM 22