M&S Systems MC111M/DM - Manual

CONGRATULATIONS!
Your purchase of an M&S SYSTEMS music and communications system is an investment that will provide years of enjoyment and service
for your customer.
M&S audio products are backed with more than 40 years of experience in the design and manufacture of precision acoustical equipment for
the home. To ensure that your customer receives the high-quality music and voice reproduction that the system is designed to deliver, it
is important that each step of the installation be done carefully. If you follow the step-by-step illustrated instructions below, the result will be
a successful professional-quality installation. In the event you need troubleshooting assistance, please call our technical staff at 1-800-366-
9422.
INSTALLATION INSTRUCTIONS
ROUGH-IN MC111M/DM SYSTEM
receptacle where
the RT11 remote
p o w e r
transformer will
be plugged in.
Label and secure
cables at master.
The door release
switch
contacts
are very versatile
and can be used
with
many
AC/DC door or
switch contacts.
Be sure to use the
wire and power
supply or transformer specified by the door or gate release
being used.
HomeMation - Home
automation
interface
(lights on, flash etc.) Run
a line of VM127X from
the master unit location to
a gang box next to a
120VAC
receptacle
where a PF284 Power
Flash module will be
installed later. Also, run a
VM127X wire from the
master location to each
N15D/N35D
remote
station. Do not bundle
the VM127X wires with
the
intercom wires!
Secure cable at master.
Refer to the HomeMation application guide for specific feature
implementation information.
M&S SYSTEMS 2-Year “No Fault” LIMITED WARRANTY
M&S Systems warrants for two years (2) all products to be free of factory-caused defects in material and
workmanship. M&S Systems will repair or replace, at its option, parts and materials at no charge, regardless of
the problem. This warranty extends to the original purchaser of the product and to each subsequent owner
of the product during the term of this warranty. This NO FAULT warranty covers only the liability described
above, and does not include liability for incidental or consequential damages. NOTE: Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
115741 C
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,ROUGH-IN,MC111 - LINEAR P/N: 115741 C - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: FLAT: 17.000” X 11.000”, FOLDED 8.500” X 11.000” - SCALE: 1-1 - FOLDING: 1-FOLD VERTICAL - SIDE 1 OF 2
☛ USE ONLY M&S SYSTEMS BRAND CABLE as called out in
these instructions. The cable is designed and constructed with electrical
specifications necessary for proper audio performance. Important:
The use of non M&S SYSTEMS brand cable will void the
product warranty! Note: All M&S SYSTEMS cable has M&S SYSTEMS
and the part number printed on it!
☛ USE or MS4XSC cable for room stations, remote controls and
volume controls.
☛ DO NOT EXCEED 200 FEET of cable for any one run or 700 FEET
for the entire system. The maximum number of stations including the
master is 10.
☛ USE or MS4DCXSC for door stations. The maximum number of
door stations is two.
☛ RUN A SINGLE CABLE from the master unit location to each room
station or control (Home Run). DO NOT LOOP CABLE from one
station to another. Looping will cause electronic feedback.
☛ DO NOT STAPLE CABLES! Staples cause shorts.
☛ DO NOT SPLICE CABLES. Splices are unreliable and defeat the
signal isolation properties of the cable
☛ KEEP CABLES AT LEAST 18 INCHES FROM
FLUORESCENT LIGHT FIXTURES, DIMMER CONTROLS,
AND ALL OTHER WIRING. This includes AC wiring, security cable,
and other control wires. These can cause a “hum” or “buzzing” sound in
the intercom.
☛ Keep cables away from objects such as heating and air conditioning ducts,
metal construction plates, and anything else with sharp edges that can
damage the cables.
☛ Outside cable runs should be underground through PVC conduit (one
cable per conduit unless shielded cable MS4XSC or MS4DCXSC is used).
This cable is not weatherproof, therefore, it must be protected. PVC
must be sealed on each end to prevent condensation in the pipe.
☛ If extra cables are run for possible future speaker additions, care must be
taken that these cables do not get connected to the master unit.
Unterminated cables (no station) connected to the master unit will cause
electronic feedback that will damage the master unit.
DO s DONT' s &
The rough-in installation should be made during new construction prior to the application of wall covering material. However, retrofit
instructions are included where applicable.
Tools required: Power drill with 1” auger, #2 Phillips screwdriver, wire stripper/cutter, tape measure and level.
Figure 14 - DRW door release strike
Figure 15 - Home automation hookup