Mirage Loudspeakers V2 - Manual (Page 3)

22
notes
11 12
13 14
OMNISAT V2 CC Table Top Mount
owners manual
3
5. Mount the wall bracket into position. The use of proper anchors for all screws is required to
ensure a secure installation. Please note that screws and anchors are not included in the
OMNISAT V2 CC package. (Diagram 10)
6. Feed the wires through the hole cut out. (Diagram 11)
7. Connect the wires to the appropriate binding posts at the back of the OMNISAT V2 CC.
IMPORTANT: Connect the speaker wire from the positive (RED +) terminal on the
amplifier to the positive (RED+) terminal on the speaker. Connect the negative
(BLACK-) terminal on the amplifier to the negative (BLACK-) terminal on the
speaker.
8. After the wires are connected, hang the OMNISAT V2 CC on the wall bracket. Center the
OMNISAT V2 CC and push down lightly on the speaker to achieve a tight fit between the
speaker and the bracket. If the speaker is not centered, repeat this step. (Diagram 12)
BOOKSHELF/ENTERTAINMENT
UNIT PLACEMENT
The small size and Omnipolar dispersion of the versatile OMNISAT V2 Satellite and OMNISAT
V2CC center channel speakers permits them to be easily placed, among other places, in a
bookshelf. To maximize the Omnipolar dispersion potential, bring the speaker as close to the
front of the cabinet as possible.
CONNECTIONS
The Mirage OMNISAT V2 series is equipped with high quality binding posts that permit the use
of banana plugs, spades, or a bare wire connection. Connect the speaker wire from the positive
(RED +) terminal on the amp to the positive (RED+) terminal on the speaker. Connect the
negative (BLACK-) terminal on the amplifier to the negative (BLACK-) terminal on the speaker.
Mirage, SCT™, and Create Your Sound™, are trademarks of Audio Products International Corp.
"Dolby", "Dolby Pro-Logic", and "Dolby Digital" are trademarks of Dolby Laboratories Licensing. "DTS"
is a trademark of Digital Theater Systems Inc.
SPECIFICATIONS:
OMNISAT V2 (Satellite)
System Type: 2-way Magnetically Shielded OMNIPOLAR Satellite
Frequency Response: 70 Hz-20KHz, +/- 3dB
Tweeter: 1" (25mm) PTH™ Pure Titanium Hybrid
Woofer: 4.5" Polypropylene Titanium Deposit Hybrid woofer
Power Handling: 150 watts
Crossover Point: 2.7 kHz
Room Efficiency: 89 dB
Impedance: 8-ohm nominal, 4 ohm minimum
Recommended 10 to 150-watts RMS/Channel
Inputs: High Quality 5-way Binding Posts
Dimensions (H x W x D in) 8.12 x 5.53 x 5.9
Dimensions (H x W x D cm) 20.62 x 14.05 x 14.99
OMNISAT V2 FS (Floorstanding model)
System Type: 2 1/2 way Magnetically Shielded OMNIPOLAR Tower with
hybrid bass loading
Frequency Response: 55Hz-20kHz, +/- 3dB
Tweeter: 1" PTH
Woofer: (1) 4.5" Poly Titanium deposit hybrid in sealed
sub-enclosure, (2) 4.5" Poly titanium deposit hybrid with
(4) 4.5" Poly titanium hybrid passive radiators
Power Handling: 175 watts
Crossover Point: 900Hz, 2.5kHz
Room Efficiency: 94dB
Impedance: 8-ohm nominal, 4-ohm min
Inputs: High Quality 5-way Binding Posts
Dimensions (H x W x D in) 45 x 5.53 x 5.9 (height includes glass base)
Dimensions (H x W x D cm) 114.3 x 14.05 x 14.99
OMNISAT V2 CC (Center Channel)
System Type: 3-way Magnetically shielded OMNIPOLAR centre channel
Frequency Response: 70Hz-20kHz
Tweeter: 3/4" PTH
Woofer: 3" Poly titanium deposit hybrid midrange, 2 x 4.5"
Poly titanium hybrid woofers with neodymium motors
Power Handling: 175 watts
Crossover Point: 700Hz, 2.7kHz
Room Efficiency: 91dB
Impedance: 8-ohms nominal, 4-ohm min
Dimensions (H x W x D in) 5.21 x 17.8 x 4.62
Dimensions (H x W x D cm) 13.23 x 45.21 x 11.73
Mirage OMNISAT V2(9 lang)-printers 2/22/05 9:06 AM Page 5