Subsidiary settings (cont.) – JVC 0105KTH-MW-BJ User Manual

Page 54

Advertising
background image

Filename [XV38ASAG_08Subsidiary.fm]

Masterpage:Left+

54

EN

Page 54

December 8, 2004 3:54 pm

SUBSIDIARY SETTINGS (cont.)

* The default setting is bold in the table below.

8 B.E.S.T.ON / OFF

You can set the B.E.S.T. (Biconditional Equalised Signal Tracking)
system to “ON” or “OFF.” (

pg. 25)

NOTES:

● When watching a tape recorded with “B.E.S.T.” set to “ON,” it

is recommended that you leave B.E.S.T. on during playback as
well.

● When watching a rental tape or one recorded on another

video recorder, or when using this unit as the player for
editing, set B.E.S.T. to your preference.

● The B.E.S.T. system works for both SP and LP modes only after

a tape has been inserted and the Record mode is first initiated.
It does not work during recording.

● The B.E.S.T. system does not work while Automatic Satellite

Programme Recording is in progress. (

pg. 32)

● In the case of timer recordings, the B.E.S.T. system works

before recording is initiated.

● Once the cassette is ejected, the B.E.S.T. data is cancelled. The

next time the cassette is used for recording, B.E.S.T. is re-
performed.

● Pressing the unit’s 7 button while “bESt” is displayed does not

start Instant Timer Recording. (

pg. 24)

8 PICTURE CONTROLAUTO (NORM) / EDIT / SOFT

This feature helps you to adjust the playback picture quality
according to your preference. Normally select “AUTO.”

AUTO

(

NORM)

: Normally select this. Picture quality is adjusted

automatically. When “B.E.S.T.” is “OFF,” “NORM” will appear
instead of “AUTO.”

EDIT

: Minimizes picture degradation during editing (recording

and playback).

SOFT

: Reduces image coarseness when viewing overplayed

tapes containing a lot of noise.

NOTES:

● When you select “EDIT” or “SOFT,” the selected mode will not

change until you select another mode.

● When you select “EDIT” to dub tapes, be sure to select

“AUTO” after you finish dubbing the tapes.

● When “B.E.S.T.” is “OFF,” “PICTURE CONTROL” switches

automatically from “AUTO” to “NORM.”

PAL/MESECAMAUTO / PAL / MESECAM

Select the appropriate colour system for recording or playback.
AUTO

: Usually set to this mode. The appropriate colour system

(PAL or MESECAM) will be selected depending on the
playback or recording signals.

If the “AUTO” mode does not work properly, select either of
the following manual modes.
PAL

: To record PAL signals, or playback a PAL tape.

MESECAM

: To record SECAM signals, or playback a SECAM or

MESECAM tape.

NOTES:

SECAM signals will always be recorded as MESECAM. Select
“AUTO” or “MESECAM” when recording SECAM signals.

When playing back a SECAM tape, select “AUTO” or
“MESECAM.” The playback picture will always be
monochrome.

NTSCNTSC3.58 / NTSC4.43 / NTSC

]

PAL

To record NTSC signals or playback a NTSC tape, it will be
necessary to select the appropriate mode.
NTSC3.58

: To record NTSC signals or playback a NTSC tape.

NTSC4.43

: To record NTSC4.43 signals or playback a NTSC4.43

tape.
NTSC]PAL: To playback a NTSC tape on PAL TV.

NOTES:

The “NTSC

]

PAL” mode does not work during recording. In

this mode, NTSC signals will be recorded as NTSC3.58.

The Menu screen is distorted during playing back a NTSC tape
on PAL TV. Stop playback and access the Menu screen again.

In the “NTSC4.43” mode, with some TVs, on-screen displays
(Program screen, etc.) may roll up or down and there may be a
loss of colour. When this happens, select the “NTSC3.58”
mode.

8 O.S.D.ON / OFF

When this function is set to “ON,” various operational indicators
appear on the TV screen. Messages appear in the selected
language. (

pg. 14, 16)

NOTES:

● When you use this unit as the source player for editing, be sure

to set “O.S.D.” to “OFF” before starting.

● During playback, the operation mode indicators may be

disturbed depending on the type of tape being used.

XV38ASAG_EN_BOOK.book Page 54 Wednesday, December 8, 2004 4:00 PM

Advertising
This manual is related to the following products: