JVC Ceiling Recessed Bracket WB-S625U - Manual (Page 2)

Attaching a Ceiling Recessed Bracket
The Ceiling Recessed Bracket can be mounted to ceiling
materials with a thickness between 5 mm to 31 mm (1/4
inch to
1 1/4 inch).
1.
2.
3.
4.
Ceiling
Recessed
Bracket
Upper
chart
Side chart
Mounting
screws
(4 locations)
Safety cable
Anchor bolt
Clamping brackets
5.
7.
Front Mark (•)
Mounting screws
(4 locations)
Stopper
165(6 1/2 inc
h)
Clamping
brackets
Clamping
screws
(3 locations)
Anchor bolt
mount hole
In the case of VN-C625U, install the Converter Unit (supplied with VN-C625U) in the ceiling before mounting the
Ceiling Recessed Bracket.
CAUTION
1.
Make a hole in the ceiling (φ165 mm (6 1/2
inch)) for inserting the Ceiling Recessed
Bracket.
2.
Remove the mounting screws.
● Use these mounting screws (4 locations) to mount the
ceiling mount of the camera.
3.
Perform the following prior to inserting the
Ceiling Recessed Bracket into the ceiling.
● Check that the orientation of the clamping bracket is as
shown in the diagram.
● If the clamping bracket is not installed all the way up, do
so by turning the clamping screws of the Ceiling Recessed
Bracket in the counter-clockwise direction. (3 locations)
4.
Insert the Ceiling Recessed Bracket into the
ceiling.
● Align the & mark on the Ceiling Recessed Bracket in the
direction that you want the camera to face, and insert the
Ceiling Recessed Bracket into the ceiling by tilting it as shown
in the diagram. The stopper will press against the rear of
the ceiling and hold the Ceiling Recessed Bracket in place.
5.
Fasten the Ceiling recessed Bracket.
● Push the Ceiling Recessed Bracket all the way upward
towards the ceiling.
● Turn the clamping screws in the counter-clockwise direc-
tion, and fasten upon clamping the ceiling material with
the clamping bracket. (3 locations)
● If anchor bolts can be used, attach M8 to M10 (or 3/8 inch)
anchor bolts into the anchor bolt mount hole on the Ceiling
Recessed Bracket and tighten using a hexagon nut.
● If anchor bolts cannot be used, ensure to install a safety
cable.
● Make sure that the clamping blackets grip the ceiling plate
firmly. If the Ceiling Recessed Bracket rattles after the
clamping screws.
● For the used safety cable, pay particular caution to the
length, strength, pull, material, etc.
CAUTION
6.
Connect cables to the Ceiling mount.
● For details, please refer to the “INSTRUCTIONS” sec-
tion of the camera in use.
7.
Attach the Ceiling mount to the Ceiling Re-
cessed Bracket.
● Attach the ceiling mount supplied with the camera to the
Ceiling Recessed Bracket, be careful not to catch the
cables. Use the mounting screws (4 locations) that have
been removed in Step 2. When attaching, align the
FRONT mark (
• ) of the ceiling mount with the & mark of
the Ceiling Recessed Bracket.
8.
Attach the camera to the Ceiling mount.
● Perform the necessary camera settings before attaching.
● For details, please refer to the “INSTRUCTIONS” sec-
tion of the camera in use.
9.
Attach the Ceiling Panel.
● Refer to “Attaching a Ceiling Panel” on the next page.
Alignment Mark ( & )
Alignment Mark ( & )
Hexagon Nut
Alignment Mark ( & )
Ceiling mount
When anchor
bolts cannot
be used
Screw driver
WB-S625U_LWT0270-001A-K 05.3.18, 10:45 AM 2