JVC BD-X201M - Manual (Page 38)

64
Setup Menu
SYSTEM MENU (2/2) screen
Parameter Possible settings Description
AC IN MODE [POWER ON]
POWER OFF
AC [oN]
oFF
SYNC SYSTEM [AUTO]
INTERNAL
SYNC [AUTo]
INTE
TV TYPE [NTSC]
PAL
TV [NTSC]
PAL
VBID OUT (WIDE) [OFF]
ON
Vbid [oFF]
oN
Y/C TERMINAL [S1]
MODE S2
Y C TM [S1]
S2
OPERATION [OFF]
LOCK ON
oPLoCK [oFF]
oN
BACK
bACK
For selecting whether to start up in the Operate ON or OFF mode when the MAIN
POWER switch at the rear of this unit is turned ON.
POWER ON : Start up in Operate ON mode
POWER OFF : Start up in Operate OFF mode
For selecting the synchronization method for this unit.
AUTO
: Switches automatically between internal and external synchronization
INTERNAL : Set to internal synchronization
For selecting the signal system during recording and playback.
NTSC : When recording/playing back in the NTSC mode
PAL
: When recording/playing back in the PAL mode
This unit will automatically be rebooted when this setting is changed.
Upon reboot, all menu items except the date/time data and hour meter will be
restored to their default values.
For selecting whether to add the JCPX-1204 standard-compliant VBID (Video Blanking
ID) signals to the analog video signals output from this unit. (NTSC only)
OFF : Do not add VBID signals (Copyguard signals will be added.
ON
: Add VBID signals
This parameter is used to set the specification for the DVD recorder’s VIDEO Y/C
INPUT and OUTPUT terminal in order to enable the recording of wide-screen
discrimination signals.
S1 : S1 terminal mode is to be adopted. A discrimination signal for normal video
with a 4:3 aspect ratio and squeezed video is to be recorded.
S2 : S2 terminal mode is to be adopted. A discrimination signal for normal video
with a 4:3 aspect ratio, squeezed video, and letterbox video is to be recorded.
Squeezed video : 16:9 wide-screen content with the left and right sides
compressed for normal aspect screens.
Letterbox video : Content with the top and bottom of the screen blackened out.
For selecting whether to enable operation lock.
OFF : Operation lock turns OFF and all operation buttons on the main unit are enabled
ON
: Operation lock turns ON and operation buttons on the main unit are disabled
However, the CLOSE/OPEN, SET UP, SET and cursor buttons will not be
disabled.
Returns to the SYSTEM MENU (1/2) Screen
65
DVD MENU Screen
The following table identifies and describes the parameters that may be set using the DVD MENU screen.
Top half
: Appearance on monitor screen
Bottom half : Appearance on LCD display
[ ]
: Default setting
Parameter Possible settings Description
EDIT MENU ENABLE
[DISABLE]
EdIT oN
[oFF]
STYLE [TYPE1]
TYPE2
TYPE3
TYPE4
TYPE5
TYPE6
TYPE7
TYPE8
BACK
STYLE [T1]
T2
T3
T4
T5
T6
T7
T8
bACK
TITLE PATTERN [1] to 6
BACK
TITL P [1] to 6
bACK
CHAPTER [1] to 6
PATTERN BACK
CHAP P [1] to 6
bACK
THUMBNAIL [NORMAL]
FORM V-CUT
H-CUT
V+H CUT
THUMb [NoR]
VCUT
HCUT
V+H
This parameter is used to indicate whether or not a screen for editing the title and
chapter menus is to be displayed when title closing or finalizing is performed.
ENABLE : The menu editing screen is to be displayed.
Upon title closing, the THUMBNAIL EDIT screen will be displayed for
the corresponding chapter menu. (
☞ Page 43)
Upon finalizing, the TITLE MENU EDIT screen will be displayed for the
title menu. (
☞ Page 49)
DISABLE : The menu editing screen is not to be displayed.
This parameter is used to select one of the eight different display styles that have
been provided for title and chapter menus. (
☞ Page 35)
BACK : returns to the DVD MENU screen.
This parameter is used to open the TITLE PATTERN screen.
That screen can then be used to select a display pattern for the title menu.
BACK : Returns to the DVD MENU screen.
* 6 cannot be selected when setting for factory shipment.
This parameter is used to open the CHAPTER PATTERN screen.
That screen can then be used to select a display pattern for the chapter menus.
BACK : Returns to the DVD MENU screen.
* 6 cannot be selected when setting for factory shipment.
Thumbnail creation method for chapter and title menus during wide-signal recording
is selected.
NORMAL : The input signal is to be converted into thumbnails without modification.
If the input video has an aspect ratio of 4:3, the corresponding thumbnails
are also to have this aspect ratio.
V-CUT : In this case, the top and bottom of the video content is to be removed to
form thumbnails.
H-CUT : In this case, the left and right of the video content is to be removed to
form thumbnails. (SQUEEZE)
V+H CUT : In this case, the top, bottom, left, and right of the video content is to be
removed to form thumbnails. (LETTER BOX)
Default settings
TYPE TITLE PATTERN CHAPTER PATTERN
1 1 1
2 2 2
3 3 3
4 4 4
5 5 5
6 1 1
7 2 2
8 3 3