JVC XL-FZ700BK - Manual (Page 13)

11
V
a
ri
ous pl
ayback
pa
tt
e
rn
s
English
Various playback patterns
Playing tracks in a desired
order (Program Play)
You can play only the favorite tracks in any desired order.
1 In stop mode, press the PROGRAM button so
that the PROGRAM indicator lights on the
display.
2 Select the disc which contains the track to be
programmed with the DISC (1-7) button. “AL”
(all tracks) appears on the display.
To program the entire disc
When the track number is not specified after
selecting the disc number, all tracks on the selected
disc are programmed.
3 Select the track number by pressing the
track buttons on the remote control unit.
To select the track number with the track buttons,
see “How to use the track buttons” on page 9.
• If you want to cancel the displayed program step,
press the CANCEL button on the remote control
unit and then enter a new disc number and/or
track number.
4 Repeat steps 2 and 3 for other tracks and/or
discs to be programmed.
You can program up to 32 steps.
5 Start playback by pressing the 3 PLAY button
on the main unit or the 3 button on the
remote control unit.
The programmed tracks and/or discs are played in
the programmed order and, when all the
programmed tracks/discs are played back, program
playback stops.
• You can skip to a desired program step with the
4/¢ buttons.
If you have programmed all discs as “AL”,
pressing
¢ (or 4) will skip to the next (or
previous) disc.
• To check the program contents
In stop mode or during playback, press the CALL
button on the remote control unit. Each time the CALL
button is pressed, the program contents are displayed
in the programmed order. (After pressing the CALL
button, perform the next button operation within five
seconds (during the program step number is
blinking).)
• To modify the program contents in stop mode
To add a new program step to the last step, enter the
new disc number and/or track number referring to
steps 2 and 3 above.
To delete the program step from the last step, press
the CANCEL button on the remote control unit. Each
time the CANCEL button is pressed, the last program
step is deleted one by one.
To delete any program step, press the CALL button to
locate the program step number you want to delete,
and then press the CANCEL button. (After pressing
the CALL button, perform the next button operation
within five seconds (during the program step number
is blinking).)
• To exit program mode in stop mode
To exit program mode, press the PROGRAM button on
the remote control unit so that the PROGRAM
indicator goes out on the display. However, the
program contents are not erased and, whenever the
program mode is selected, you can play the tracks in
programmed order.
• To clear the entire program contents
In stop mode, press the CANCEL button on the remote
control unit repeatedly until entire program contents
are deleted. Or, press the
0 OPEN/CLOSE button on
the main unit or the OPEN/CLOSE button on the
remote control unit.
Even after the entire program contents have been
cleared, the unit remains in program mode.
Note that turning off the unit does not clear the
program contents.
If the AC power cord is disconnected from the outlet,
the program will be erased.
PROGRAM
Remote control unit
DISC TRACK TIME STEP
PROGRAM
1 2 3
5 6 7
4
1 2 3 4 5 6
7 8 9 10 11 12
13 14 15 16 17 18
Shows that a disc is loaded
PROGRAM indicator AL (all tracks) Program step number
ex.) When disc 4 is selected.
2 3 4 1
6 7 8 5
10 +10 9
DISC TRACK TIME STEP
PROGRAM
1 2 3
5 6 7
4
1 2 3 4 5 6
7 8 9 10 11 12
13 14 15 16 17 18
Remote control unit
Track number selected for the program step 1
Shows the disc being programmed
ex.) When track 5 is selected.
XL-FZ 700BK(UJ).book Page 11 Friday, April 19, 2002 6:05 PM