JVC LPT0715-001A - Manual (Page 32)

32
S
HOW
V
IEW
® -Recording
Example: You receive NBC on program position 12.
In case of the first S
HOW V IEW -recording for NBC, 2 bars
will blink at the CH-line. Enter 12 with number keys.
Press 1 and then 2 within 2 seconds (if the 2-press was
too late, the display 1 will be replaced with 2). The
S
HOW V IEW -system memorizes that the storing position
12 is for NBC. From the next all times of the S HOW V IEW -
recording from NBC, the 12 will be entered in the “CH”-
line automatically. In case of an erroneous input for the
channel number, press
to go in the “CH”-line and
enter the correct number again.
Press / or number
keys to enter the program
position number.
Then press
.
Setting a day of the week:
You have selected DAILY or WEEKLY in step 3, then
you can select recording date again. The date must blink
as 2 bars.
If it does not blink, then press
or repeatedly until
the DATE blinks. Then press or repeatedly until
the desired date appears.
The following date are stand for your selection: SUN-
SAT: all dates from Sunday to Saturday, or MON-SAT:
only dates from Monday to Saturday, or MON-FRI: only
dates from Monday to Fryday. WKL-MON: each Monday,
WKL-TUE: each Tuesday, ..., WKL-SUN: each Sunday.
Change the recording start-time:
The recording start-time will be set by S HOW V IEW
automatically. However you can change the recording
start-time manually. The time near START must blink.
If it does not blink, press
or repeatedly until the
time blinks. Then press to change.
Recording period extension:
The recording end-time will be set by S HOW V IEW
automatically. However you can extend the recording
end-time manually. The time near END must blink.
If it does not blink, press
or repeatedly until the
time blinks. Then press to extend.
Select Tape speed:
Select the recording tape speed Standard Play (SP) or
Long Play (LP).
Press
or repeatedly until you are in SPEED-line.
Then press or to select “SP” or “LP”.
DATE 15 TUE
17:30
18:00
START
END
CH
SELECT :
SET :
EXIT : MENU
SHOWVIEW NO . 327741029
SPEED SP
12 NBC
/ 0–9
OK : OK
VPS/PDC OFF
VPS/PDC:
Switch the VPS/PDC on or off. Be sure to pay attention
to the VPS/PDC-important note on page 35.
Press
or repeatedly until you reach VPS/PDC-
line.
Then press
or to select “ON” or “OFF”.
5
Press OK after the
confir mation. Then
press SET UP MENU
repeatedly until the TV-
picture appears.
To enter the other
program repeat the
steps 1 - 5.
6
Press •. The clock symbol ( ) will appear on the
display and the VCR stands by for recording. At the
same time, VCR mode will change to DVD mode
automatically. You can use DVD even if the VCR is
in the Timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before
the time you predetermined.
Note:
• If the clock symbol (
) does not appear on the
display in spite of the pressing of •, the cassette
may not have been loaded yet.(see page 22)
• If the cassette is ejected in spite of the pressing
of •, the erase prevention tab of the cassette may
have been removed. (see page 22)
• If the clock symbol ( ) blinks when the timer re-
cording ended, the TV program has not been com-
pletely recorded because of an insufficient tape sup-
ply. In this case, press • to cancel the timer pro-
gram or press EJECT to remove the cassette tape.
• During timer recording standby mode, the VCR
mode cannot be selected. To use the VCR, press
• at first, then press VCR to change to VCR mode.
After you use the VCR, press • again to put the
VCR into timer recording standby mode.
• If you press • during timer recording, the record-
ing operation will be interrupted. If you press •
again within the programmed time, the recording
operation will start again.
--:-- --:-- ------ --
17:30 18:00 7V 15 TUE
--:-- --:-- ------ --
--:-- --:-- ------ --
--:-- --:-- ------ --
--:-- --:-- ------ --
SELECT :
EXIT : MENU
/ OK
--:-- --:-- ------ --
--:-- --:-- ------ --
-
-
-
-
-
-
-
SP
2A73501AE(28-33) 4/17/02, 8:25 PM 32