Activating the surround/dsp modes, English, When you select “auto surr” (auto surround) – JVC RX-F31S User Manual

Page 41

Advertising

English

On the front panel:

Before you start, remember...

There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step

2 again.

Select and play any source other than “DVD
MULTI.”

• Make sure you have selected the input mode (analog or

digital) correctly.

Press SURROUND.

MULTI JOG now works for selecting Surround/DSP modes.

Turn MULTI JOG to select the Surround/DSP
mode you want.

Ex.: When “DOLBY D” is selected for Dolby Digital multi-

channel software:

To cancel Surround/DSP modes

Turn MULTI JOG so that “SURR OFF” appears on the display.

NOTE

The initial setting is “AUTO SURR.”

* Available Surround modes vary depending on the incoming

signals. For details, see “Using the Surround/DSP modes” on
page 38.

When you select “AUTO SURR” (Auto Surround)

You can enjoy the Surround mode easily.
• For details about the Surround modes, see pages 34 to 36.
• When “AUTO SURR” is activated, the AUTO SR indicator lights

up on the display.

How does “AUTO SURR” work?

• If a multi-channel signal comes in, an appropriate Surround

mode will be selected automatically.

• If a Dolby Digital 2-channel or DTS 2-channel signal with

surround signal comes in, “PLII MOVIE” will be selected.

• If a Dolby Digital 2-channel or DTS 2-channel signal without

surround signal, or a Linear PCM signal comes in, “SURR
OFF (stereo)” will be selected.

NOTES

• “AUTO SURR” does not take effect in the following cases:

– While playing an analog source.
– While selecting one of the fixed digital decode modes—

“DOLBY D” or “DTS” (see page 13).

• While listening with the headphones, the 3D HEADPHONE

mode (see pages 36 and 37) is activated without respect to the
type of software played back.

• When “AUTO SURR” is selected, sound may not come out at

the beginning of playback. If it occurs, select a Surround mode
manually.

Activating the Surround/DSP modes

Available Surround/DSP modes vary depending on the incoming
signals. For details, see page 38.

Activating one of the Surround/DSP modes automatically
recalls the memorized settings and adjustments.

• To adjust the speaker output level, see page 29.

• To adjust the effect level for the DSP mode (except All

Channel Stereo mode,) see page 31.

• To add “wraparound” sound effect to “PLII MUSIC”

(PANORAMA control,) see page 31.

• To adjust the sound localization of the center channel

for “NEO:6 MUSIC” (center gain,) see page 31.

• To adjust the vertical localization of the center channel

for Surround/DSP modes (except “PLII MUSIC,” “PLIIx
MUSIC,” “Neo6: MUSIC,” and “ALL CH ST”) (center
alignment,) see page 31.

NOTES

• You cannot use any Surround/DSP modes when selecting “DVD

MULTI” as the playback source.

• The on-screen display appears on the TV screen to show the

Surround/DSP mode name for 5 seconds when you select the
Surround/DSP mode.
To cancel the function, set “SUPERIMPOSE” to
“SUPERIMPOSE: OFF” (see page 25).

From the remote control:

Select and play any source other than “DVD
MULTI.”

• Make sure you have selected the input mode (analog or

digital) correctly.

Press SURROUND repeatedly to select the
Surround/DSP mode you want.

Ex.: When “DOLBY D” is selected for Dolby Digital multi-

channel software:

To cancel Surround/DSP modes

Press SURROUND repeatedly so that “SURR OFF” appears on
the display.

1, 3

EQ
LPCM

S . WFR

NEO : 6
DSP 3D

LFE

DOLBY D

DTS AAC
96 / 24

AUTO SR

C.TONE VIRTUAL SB AUDIO P. BASS

TA NEWS INFO RDS TUNED ST

SLEEP

AUTO MUTING

AUTO MODE

ATT
HP
MHz

kHz

HALL1

HALL2

THEATER1

THEATER2

(Back to the beginning)

LIVE CLUB

AUTO SURR

DANCE CLUB

PAVILION

ALL CH ST

MONO FILM

Surround modes*

SURR OFF

When operating the receiver
using the remote control, set the
mode selector to
“AUDIO/TV/VCR/DBS.”