Using the surround/dsp modes, Virtual surround back, About the dsp modes – JVC RX-F31S User Manual
Page 91
38
Virtual Surround Back
This function creates the great surround effect from the behind as if you have connected the surround back speaker. The VIRTUAL
SB (Surround Back) indicator lights up on the display.
If you have connected (and activated) the surround speakers, you can use Virtual Surround Back without connecting the surround
back speaker.
Virtual Surround Back is activated when “EX/ES/PLIIx” is set to other than “EX/ES/PLIIx: OFF” and when playing back the software
including the following signals:
– Dolby Digital Surround EX
– DTS-ES
– Dolby Digital or DTS with more than 4-channels
Virtual Surround Back is activated when one of the Surround modes is selected.
Using the Surround/DSP modes
Available Surround/DSP modes vary depending on the speaker settings and the incoming signals. See the table below.
• The numbers inside the parentheses following the incoming signal type indicate the number of the front channels and that of the
surround channels. For example, (3/2) indicates that the signals are encoded with three front signals (left/right/center) and two (stereo)
surround signals.
• For EX/ES/PLIIx setting, see page 22.
The name of the mode shown below is the display indication.
EX/ES/PLIIx setting
AUTO
ON
PLIIx MOVIE
PLIIx MUSIC
OFF
Dolby Digital Surround EX
DOLBY D EX*
2
*
5
DOLBY D EX*
2
DOLBY D EX*
2
*
3
D + PLIIx MU*
2
DOLBY D
Dolby Digital (3/2, 2/2)
DOLBY D
DOLBY D EX*
2
DOLBY D EX*
2
*
3
D + PLIIx MU*
2
DOLBY D
Dolby Digital (3/1, 2/1, 3/0, 1/0)
DOLBY D
Dolby Digital (Dual Mono)
DUAL MONO
DTS-ES Discrete*
1
ES DISCRETE*
2
ES DISCRETE*
2
DTS +
EX*
2
*
3
DTS + PLIIx MU*
2
DTS
DTS-ES Matrix*
1
ES MATRIX*
2
ES MATRIX*
2
DTS +
EX*
2
*
3
DTS + PLIIx MU*
2
DTS
DTS (3/2, 2/2)*
1
DTS
DTS + NEO:6*
2
DTS +
EX*
2
*
3
DTS + PLIIx MU*
2
DTS
DTS (3/1, 2/1, 3/0, 1/0)
DTS
DTS (Dual Mono)
DUAL MONO
Dolby Digital (2/0)
DTS (2/0)
PLIIx MOVIE*
4
/PLIIx MUSIC*
4
/NEO:6CINEMA/NEO:6 MUSIC
Lenear PCM
Analog
DVD MULTI
None
Incoming Signal Type
Dolb
y Digital
*
1
DTS 96/24 processing is not applied when the EX/ES/PLIIx setting is activated. If you want to apply the processing, set the EX/ES/
PLIIx setting to “EX/ES/PLIIx: OFF” (see page 22).
*
2
When “SURROUND BACK SPEAKER” is set to “SURR. BACK SPK: NO” (see page 21), Virtual Surround Back is activated for the
modes.
*
3
When using PLIIx Movie to reproduce Dolby Digital or DTS software, this receiver applies Dolby Digital EX (DOLBY D EX) or DTS plus
Dolby Digital EX (DTS +
EX) processing (6.1-channel reproduction) to the software.
*
4
When “SURROUND BACK SPEAKER” is set to “SURR. BACK SPK: NO” (see page 21), “PLIIx MOVIE” is changed to “PLII MOVIE”
and “PLIIx MUSIC” is changed to “PLII MUSIC.”
*
5
For some Dolby Digital Surround EX software, Dolby Digital 5.1-channel reproduction (“DOLBY D”) may be applied. In this case, select
“EX/ES/PLIIx: ON” to apply “DOLBY D EX.”
About the DSP modes
• The following DSP modes are available regardless of incoming signal type:
HALL1, HALL2, LIVE CLUB, DANCE CLUB, PAVILION, THEATER1, THEATER2
• When an incoming signal is a multi-channel (more than 2-channel) digital signal, “MONO FILM” is not available.
• You cannot select “ALL CH ST” when the surround speakers are set to “NO” in the speaker setting (see page 21).
DTS
PLII MOVIE
PLII MUSIC
NEO:6CINEMA
NEO:6 MUSIC
EN34-39RXF31S[UJ]2.p65
05.5.13, 16:58
38