JVC 0505NYMCREBET - Manual (Page 17)

14
Using the CD Player
En
g
li
s
h
Programming the Playing Order
of the Tracks
You can program the playing order of the tracks on all the CDs.
Note that you can only make a program when the CD Player is
stopped.
❏ You can program up to 32 tracks in any desired order including
the same tracks.
For MP3 discs
• If you try to select a MP3 disc that has once been read or
played, “MP3 DISC” appears on the display and it can not
be programmed.
• MP3 disc that has not ever been read can be selected in
a program mode. But when playback starts, “MP3 DISC”
appears on the display, the program is deleted and
switched to a next program.
To Make a Program
1 Load CDs.
2 In Stop mode, set the CD Player in Program
Play mode.
On the Remote Control ONLY
Press the PROGRAM/RANDOM button, and the “PROGRAM”
indicator lights up on the display.
Each time you press the button, the display changes as follows:
PROGRAM
= RANDOM = Blank display (Normal Play) =
(back to the beginning)
• If a program is already made, the last step of the program will
be displayed.
3 Press one of the Disc button (CD1-CD3) to
select the CD you want to program.
The display will change to the Program Entry display.
4 Select the track you want to program.
Using the Remote Control
Press the numeric keys to directly enter the track number. Then,
the program order number will be assigned from P-1.
Using the Unit
While the display is blinking, press the
4 or ¢ button to select
the track, then press the SET/DISPLAY button.
The program order number will be assigned from P-1.
5 Repeat steps 3 and 4 to program other tracks
on the same CD or the other CD.
6 To play the program, Press the CD
6
but-
ton.
For details, see “To Play the Program You Have Made” men-
tioned below.
To confirm the programmed contents, while the CD player
is stopped, select Program mode by pressing the PROGRAM but-
ton and press the
4 or ¢ button on the Remote Control.
To delete all the tracks in the program, while the CD Player
is stopped, press the
7 button or open the tray by pressing the CD
Open/Close
0 button.
To Modify the Program, while the CD Player is stopped and the
program mode is selected, press the CANCEL/DEMO button, the
last track in the program is deleted. To add new tracks to the end
of the program, repeat above steps 3 and 4.
• If you try to program a track number that does not exists
on the CD, your entry will be ignored.
• If you try to program the 33rd track, “FULL” appears on
the display.
To Play the Program You Have Made
Press the CD
6 button.
The System plays the tracks in the order you have programmed
them.
• To use Repeat Play for Program Play, press the REPEAT but-
ton to display “REPEAT” before starting playback. For details,
see “Repeating Tracks” on page 15.
❏ You can skip to a particular program track by pressing the 4
or
¢ button during Program Play.
❏ To stop playing, press the 7 button once. If you press the 7 but-
ton, while the CD Player is stopped, the program is deleted.
To Exit and Re-enter Program Play
The program you have made is stored in memory. So, you can exit
Program Play temporarily or re-enter Program Play unless you de-
lete the program.
To exit the program mode once, press the
7 button to stop
playing. The “PROGRAM” indicator goes off and the Program
mode will be canceled. The program is stored in the memory.
To re-enter Program Play mode, press the PROGRAM/
RANDOM button until the “PROGRAM” indicator lights up
again.
• When the power is turned off (standby mode), the stored
memory will be deletde.
Disc number
or
Track number
Disc number Track number
Program order
number
LVT1346-001A_E.book Page 14 Wednesday, May 4, 2005 11:38 AM