Jensen Phase Linear UV8020 - Manual (Page 5)

1
UV8020
PREPARATION
Congratulations on your purchase of the Phase Linear
UV8020 Mobile Multimedia Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Phase Linear
UV8020 installed by a reputable installation shop.
Features
DVD
•
Aspect Ratio - Full and Normal
• Fast Forward/Backward - 2X, 4X, 8X and 20X
• Play, Pause, Stop, Next Chapter and Previous Chapter
CD / MP3 / WMA
•
ID3 Tag Compatible
• Directory Search (MP3 / WMA Only)
• Direct Track Access via Remote Control
• Burn up to 1500 MP3 and WMA Files onto a DVD+R /
RW
• Random, Repeat and Intro
• Play, Pause, Stop, Next Track and Previous Track
AM-FM
•
30 Station Presets (18 FM / 12 AM)
• Auto Stereo / Mono
• Auto Store / Preview Scan
Auxiliary Input
•
Front Auxiliary Input (audio and video)
• 2.5mm to 3.5mm A/V Cable Included
• 2.5mm to RCA A/V Cable Included
Chassis
•
2.0 DIN (Import / ISO-DIN Mountable)
• Motorized Slide Down LCD Screen
• 7" TFT Active Matrix LCD w/ Anti-Glare Coating
• 336,960 Sub Pixels (1440W X 234H)
• Pixel Pitch - 0.107 X 0.370
• Screen Tilt / Angle Adjustment
• Beep Tone Confirmation (On-OFF Option)
General
•
44-Key Infrared Remote Control
• Two Composite Video Outputs for Additional Screens
• Three Preset EQ Curves
• Front, Rear and Subwoofer Line Output
• Programmable Volume Control
• Rear Camera Input (Normal and Mirror Image View)
• Touch Screen Calibration Mode
• 2VRMS Line Output - All Channels
What’s in the Box
1. Left and Right Double DIN Mounting Brackets
2. Double DIN Sleeve
3. Remote Control with Battery
4. Two Custom Cosmetic Trim Rings
5. Screen Cleaning Cloth
6. M5x6 and M3x4 Screws to Mount Radio to Brackets
7. Speaker Output Harness
8. Power Input Harness
9. 2.5mm to 3.5mm Accessory Cable
10. 2.5mm to RCA Accessory Cable
Tools and Supplies
You will need these tools and supplies to install your UV8020:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident (except
when using for rear view video camera) never use the
video display function while driving the vehicle. This is a
violation of federal law.
WARNING! Never disassemble or adjust the unit.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Using an improper fuse may cause damage
to the unit and result in a fire.
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
NOTE: If the UV8020 is to be installed in a car equipped
with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.