JVC LX-D1000 - Manual (Page 2)

– 2 –
CHECK AND MAKE SURE
Check and confirm before assembly and/or installation that the following parts are packed along with the body as accessories:
CAUTION: When installing component parts, caution must be
exercised not to use any parts except the ones packed with the body.
PROCEDURES FOR ASSEMBLY AND INSTALLATION
(Refer to Fig. 3)
1. To begin with, determine the projection range, then the fixing posi-
tion of the metal fixtures’ ceiling plate. (The projection lens center of
the ceiling plate is apart about 24 mm from that of the LCD projector.
Refer to Fig. 4)
2. Install the ceiling plate underneath the ceiling as illustrated in Fig. 3.
For the size of the metal fixtures’ fixing hole, refer to Fig. 3-1. Use
the fixing screw of the ceiling plate larger than M8.
WARNING: Check and make certain that there is a safety rate of
more than 5 for the total mass of the metal fixtures including the
LCD projector.
3. Turn the LCD projector over, and loosen only the angle adjuster lo-
cated at the position illustrated in the figure. See Fig. 1. (At this
time, take the sponge out from between the angle adjuster and the
body.)
4. Set the body’s plate to the LCD projector, and slide it in the direction
indicated by the arrow mark. See Fig. 2.
5. Insert the 2 screws [A] into the two holes provided at the bottom of
the LCD projector, and tighten the angle adjuster. (See Fig. 2 and
Fig. 3)
6. Set the supporter for the LCD projector from the bottom, tighten the
screws [B], and secure the supporter.
7. Set the inner pole fixing plate and the inner pole temporarily with 4
hexagon socket bolts (M5 × 10) as illustrated in Fig. 3, and insert the
inner pole into the hole of the coupling plate.
8. Fix the inner pole fixing plate and the coupling plate with 4 hexagon
socket bolts (M5
×
16), and tighten them with 4 nuts (for M4).
9. Adjust the holes of the inner pole and the ceiling plate, put on the
collar, washer, and nut in the order as shown in Fig. 3, and fasten
them with a hexagon bolt [C].
10. Make adjustments on the rotating direction of the entire body of the
metal fixtures, and then tighten the 4 hexagon socket bolts (M5
×
10) that were temporarily fixed as mentioned in Procedure 7 above.
11. Tighten the inner pole using 2 rotary setscrews [E], and furthermore
secure the inner pole using 2 rotary mini screws.
Loosen this portion of
the angle adjuster
counterclockwise.
Fig. 1
(Bottom view of LCD projector)
Fig. 2
Slide
Angle adjuster
Body’s plate
t Screws [A] (M4 × 12)
No. Names of parts Quantity
!1 Hexagon head bolts [C] (M10
×
65) 1
!2 Nut 1
!3 Washers (for M10) 2
!4 Screws [B] (M8
×
14) 2
!5 Hexagon wrench (for M5) 1
!6 Hexagon wrench (for M8) 1
!7 Rotary mini setscrews (M5
×
5) 2
!8 Hexagon socket bolts (M5
×
16) 4
!9 Washers (for M5) 4
@0 Nuts (for M5) 4
No. Names of parts Quantity
q Coupling plate 1
w Supporter for LCD projector 1
e Assembling bolts (M8
×
25) 4
r Rotary setscrews [E] (M5 × 10) 2
t Screws [A] (M4 × 12) 2
y Ceiling plate 1
u Inner pole 1
i Inner pole fixing plate 1
o Hexagon socket bolts (M5
×
10) 4
!0 Collar 1
(*) Part
: The asterisked fastening bolt to install an arm (1 bolt)
is built in to constitute a part of the body’s plate.
: Never remove the above-mentioned bolt under any
circumstances since it is absolutely required to
ensure safety.
(*) Fastening bolt to
install arm (1 bolt)
WARNING