Jwin JC-CD260 - Manual (Page 2)

-- 3 -- -- 2 --
14.MUTE BUTTON
Press the MUTE button to stop and the LCD will flash "MUTE".
To stop this function press again the same button.
15. SCAN BUTTON
Press this button briefly (LESS THAN 2 SEC.)and the radio will tune to the next
memory preset station, pausing for 6 seconds, and repeating the process endlessly until
a selection is mode.
To stop scanning, press this button once again, or press the preset button briefly
that corresponds to the channel number blinking on display.
16.PANEL RELEASE BUTTON
Press the button and the right-side section of the panel will release.
2) menu2:BEEP ON--BEEP OFF
The situation of beep sound is selected.The 2 mode is selected as also vol up
or vol dn key.
BEEP ON mode: A beep sound is generated when each key is pressed.
BEEP OFF mode: The beep sound is disabled.
3) menu3:VOL LAST--VOL Addition
4) menu4:SEEK1--SEEK2
SEEK1:SEEK is activated right away when key is pressed for longer than 500ms.
SEEK2:SEEK is activated after key is released.
5) menu5:ESP12--45 OPTION
THE ANTI-SKIP PROTECTION FUNCTION (ASP)
Whilef in use,the player is likely to receive shocks or vibrations.The ANTI-SHOCK FUNCTION
is active to provide uninterrupted playback.
Should the player receive shocks for more than 45 seconds continuously in cd playback or
120 seconds in mp3 playback,the sound will mute for a very short while and will resume on-
ce the player has stabilised from the shock.
ESP12:Selected ESP time 12 seconds.
ESP45:Selected ESP time 45 seconds.
6) ENTER:User can select track/files and do character search while in Mp3 MODE.
VOLUME LEVEL is determined when POWER ON
LAST VOLUME:Final VOLUME LEVEL generates power before power off.
ADJUST VOLUME:VOLUME LEVEL selected by the user is produced.
4. LOUDNESS BUTTON
-Press this button to boost the bass and treble response.Push the button again to return to
normal operation.This function is useful when listening at low levels.loudspeakers are ineffici
ent at low power levels and will tend to sound flat.The loudness control will boost the bass
and treble response thus giving a more lively performance.
While this function is operating,the display shows LUD.
5. LCD DISPLAY
-The liquid crystal display will display the current status of the unit.
6. BAND SELECTOR SWITCH
Press this switch to select the desired Radio band.Selection is made in regular sequence as FM-AM.
7. AUTOMATIC OR MANUAL TUNING(FREQ UP>>OR FREQ DOWN<<)
(A) RADIO MODE
When pressed for less than 1 second,these keys operate as manual tuning mode.
When pressed longer than 1 sec.,they are operated as SEEK tuning mode.(AUTO)
(B) CD PLAYER MODE
When pressed for less than 1 second,these keys operate as TRACK UP or TRACK DOWN.
When pressed longer than 1 sec.,they will operate as CUE or REVIEW mode.
8. LOCAL/DISTANT BUTTON
Press local/distant(LO/DX) button for listening to weak stations.LOC indicator will appear on the display.
Press this button again (Distant mode) for normal operation.
9. DISPLAY BUTTON (Set the Clock)
Selects radio frequency or clock display.
To set the clock:
1.With clock display selected,hold down the (CLK) button until clock display starts flashing.
2.Press (-) to change minutes,(+) to change hours.
3.Press (CLK) button to start the clock.
10. PRESET STATIONS
Six numbered preset button store and recall stations for each band.
Storing station
1.Select a band (if needed)
2.Select a station
3.Hold a preset button longer than one second.Preset station number appears in the display when
station is saved.
Recall a station:
1.Select band (if needed)
2.Press a preset button for less than one second to select stored station.
11. AUTOMATICALLY STORE STATIONS
Select six stations and store them in current band.
1.Select a band (if needed)
2.Hold A/PS button for more than three seconds.The new station replace stations already stored
in that band.
Preset A/PS
1.Select a band (if needed)
2.Touch A/PS for more than one second but less than three seconds.Radio pauses for five seconds
at each station.Touch A/PS again to stop scanning when the desired station is reached.
12.STEREO/MONO SELECTOR
This function will only affect FM reception.Press this button if the FM reception becomes noisy/hissy.
If the station being received is in stereo,it will now be played in mono.Press this button again to return
tthe receiver to normal reception
13.MODE BUTTON (MODE)
By pressing this key,user can select RADIO mode,AUX mode,CD PLAYER mode.
FLAT M
ROCK M
CLASSIC M
POP M
LCD DISPLAY
ROCK
CLASSIC
POP
BASS (F=100HZ)
0 dB
MID (F=1KHZ) TREBLE (F=10KHZ)
0 dB 0 dB
6 dB 2 dB 0 dB
2 dB 2 dB 0 dB
-4 dB -2 dB 0 dB
DSP OFF X dB X dB 0 dB NORMAL
FLAT
8. LOCAL/DISTANT BUTTON
Press local/distant(LO/DX) button for listening to weak stations.LOC indicator will appear on the display.
Press this button again (Distant mode) for normal operation.