JVC SP-UXP5 - Manual (Page 12)

– 9 –
Common Operations
Turning On the Power
When you press the play button — CD 3/8, TAPE 2 3, or
the source selecting button — FM/AM, and MD/AUX (UX-
P6R and UX-P5R) or AUX (UX-P4R and UX-P3R), the unit
automatically turns on and starts playback if the source is
ready.
To turn on the unit, press (STANDBY/ON).
For UX-P6R and UX-P5R:
The STANDBY/ON lamp on the unit lights green.
For UX-P4R and UX-P3R:
The STANDBY lamp on the unit goes out.
To turn off the unit (on standby), press (STANDBY/
ON) again.
For UX-P6R and UX-P5R:
The STANDBY/ON lamp lights red.
For UX-P4R and UX-P3R:
The STANDBY lamp lights up.
• The CLOCK indicatior flashes on the display until you set
the built-in clock. After setting the clock, the clock time
will appear on the display while the power is off.
• A little power is always consumed even while the unit is on
standby.
To switch off the power supply completely, unplug the AC
power cord from the AC outlet.
When you unplug the AC power cord or if a power
failure occurs
The clock is reset to “0:00” right away, while the tuner preset
stations (see page 11) will be erased in a few days.
Setting the Clock
Before operating the unit any further, first set the clock built
in this unit. When you plug the AC power cord into the wall
outlet, the CLOCK indicator starts flashing on the display.
You can set the clock whether the unit is on or off.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
On the unit ONLY:
1
Press CLOCK for more than 2
seconds.
The hour digits start flashing on the display.
2
Press
¢ or 4 to adjust
the hour, then press CLOCK.
The minute digits start flashing on the
display.
3
Press
¢ or 4 to adjust
the minute, then press
CLOCK.
The CLOCK indicator remains lit on the
display.
To check the clock time
Press DISPLAY on the remote control (or CLOCK
on the unit) while playing any source.
• Each time you press the button, the source
indication and the clock time alternate on the
display.
• When you unplug the AC power cord or if a power failure occurs,
the clock loses the setting and is reset to “0:00.” You need to set
the clock again.
• The clock may gain or lose 1 to 2 minutes per month.
Selecting the Sources and Starting Play
To play back CDs, press CD
3/8. (See pages 14 – 16.)
To play back tapes, press TAPE
2 3. (See page 17.)
To listen to the FM/AM (MW/LW) broadcasts, press FM/
AM. (See pages 11 – 13.)
To select the external equipment as the source,
press MD/AUX (UX-P6R and UX-P5R) or AUX (UX-P4R
and UX-P3R.)
CD TAPE MD/AUX
STANDBY/ON
STANDBY / ON
CLOCK
CLOCK
CLOCK
CLOCK
FM/AM
STANDBY/ON
CLOCK
CLOCK
DISPLAY
CLOCK
AUX
UX-P6R and UX-P5R
UX-P4R and UX-P3R
STANDBY
STANDBY / ON
UX-P6R and UX-P5R UX-P4R and UX-P3R
EN01-13.UX-P5R&3R[B] 01.1.16, 4:32 PM 9