Before using the washing machine – Smeg TLS8 User Manual

Page 2

Advertising
background image

GB 2

BEFORE USING THE WASHING MACHINE

1.Remove the packaging and check

a. Cut and remove the shrink-wrap.

b.Remove the top protection and the protective

corners.

c. Remove the bottom protection by tilting

and turning the washing machine on one

rear bottom corner. Make sure that the

black plastic part of the bottom protection

(if available on the model) remains in the

packing and not in the machine bottom.

This is important, as otherwise the plastic part could

damage the washing machine during operation.

d.Open the lid by pressing it slightly down while

raising the handle. Remove the polystyrene

cushion (depending on model).

e. Remove the blue protective film from the panel

(depending on model).

After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local retailer.

Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children;

they are potentially dangerous.

If the appliance was exposed to the cold prior to

delivery, keep it at room temperature for a few

hours before operating.

2.Remove the transport bracket

The washing machine is fitted with transport

screws and a transport bracket to prevent

damage during transport. Before using the

washing machine you must remove the

transport bracket (see “Installation”/“Removal

of transport bracket”).

3.Install the washing machine

Place the washing machine on a flat and stable

floor surface.

• Adjust the feet to ensure that the machine

is stable and level (see “Installation”/

“Adjust the feet”).

In case of wooden or so-called “floating floors”

(for instance certain parquet or laminate floors),

place the appliance on a 40 x 60 cm sheet of

plywood at least 3 cm in thickness which is

secured to the floor.

4.Water supply

Connect the water supply inlet hose in

accordance with the regulations of your local

water company (see “Installation”/“Connect the

water inlet hose”).

Water supply: Cold water only

Tap:

3/4” threaded hose connection

Pressure:

100-1000 kPa (1-10 bar).

Only use new hoses for connecting the washing

machine to the water supply. Used hoses must

not be used anymore and should be discarded.

5.Drain hose

Connect the drain hose to the siphon or hook it

over the edge of a sink with the “U” bend (see

“Installation”/“Connect the water drain hose”).

If the washing machine is connected to a built-in

drainage system, ensure the latter is equipped

with a vent to avoid simultaneous loading and

draining of water (siphoning effect).

6.Electrical connection

Electrical connections must be carried out by a

qualified technician in compliance with the

manufacturer’s instructions and the current

standard safety regulations.

The technical data (voltage, power and fuses) are

given on the rating plate on the rear of the

washing machine.

The washing machine must be connected exclusively

by means of a socket with an earth connection in

accordance with current regulations. The washing

machine must be earthed by law. The manufacturer

declines all liability for injury to persons or animals or

damage to property deriving directly or indirectly

from failure to observe the directions.

Do not use extension leads or multi sockets.

Before any maintenance on the washing machine

disconnect it from the mains supply.

Access to the mains plug or to disconnection from

the mains supply via a double-pole switch must be

ensured at all times following the installation.

Do not operate the washing machine if it has

been damaged during transport. Inform the

After-Sales Service.

Mains cable replacement is only to be carried out

by After-Sales Service.

The washing machine must be connected to an

effective earthing installation, in compliance with

the regulations in force. In particular, washing

machines installed in premises containing a shower

or a bath must be protected by a differential

residual current device of at least 30 mA. Earthing

the washing machine is obligatory under the law.

The manufacturer declines all liability for injury to

persons or animals or damage to property deriving

either directly or indirectly from failure to observe

the directions above.

The washing machine may only be used in the

household for the prescribed uses.

Dimensions:

Width:

400 mm

Height:

900 mm

Depth:

600 mm

IFU-TL HR GB.fm Page 2 Thursday, June 7, 2007 2:23 PM

Advertising
This manual is related to the following products: