Sony MK7807V1 - Manual (Page 84)

Specifications
Inputs/outputs
Serial digital input:
SDI IN connector (BNC type) (1)
0.8 Vp-p
؎10%, 75 Ω
525/625 component serial digital signal
conforming to SMPTE259M-C (ITU-R
BT.601/BT.656), 270 Mb/s
Serial digital outputs:
Active-through output connectors (BNC
type) (4)
0.8 Vp-p
؎10%, 75 Ω
Serial digital video signal of the same
format as that to the input connector
SDI OUT connectors (BNC type) (4)
0.8 Vp-p
؎10%, 75 Ω
Serial digital video signal of the same
format as that to the input connector
Analog outputs:
MONITOR OUT connectors (BNC type) (4)
4 NTSC/PAL composite analog video
signals or 1 each R/G/B signals or 1 each
Y/U/V signals and 1 NTSC/PAL composite
analog video signals
RGB signals:
R: 0.7 Vp-p, 75
Ω
G: 0.7 Vp-p, 75 Ω
B: 0.7 Vp-p, 75 Ω
YUV (CCIR level, 625 mode only) signals:
Y: 1.0 Vp-p, 75 Ω (incl. Y sync 300 mV)
B-Y: 0.7 Vp-p, 75 Ω
R-Y: 0.7 Vp-p, 75 Ω
Defined with the color bar signal
100/0/100/0
YUV (Betacam 7.5% setup, 525 mode only)
signals:
Y: 1.0 Vp-p, 75 Ω (incl. Y sync 286 mV)
B-Y: 0.7 Vp-p, 75 Ω
R-Y: 0.7 Vp-p, 75 Ω
Defined with the color bar signal
100/7.5/77/7.5
YUV (Betacam 0% setup, 525 mode only)
signals:
Y: 1.0 Vp-p, 75 Ω (incl. Y sync 286 mV)
B-Y: 0.756 Vp-p, 75 Ω
R-Y: 0.756 Vp-p, 75 Ω
Defined with the color bar signal 100/0/75/0
NTSC composite video (525 mode only)
signals:
1.0 Vp-p, 75 Ω (incl. Y sync 286 mV)
Defined with the color bar signal
100/7.5/77/7.5
PAL composite video (625 mode only) signal:
1.0 Vp-p, 75 Ω (incl. Y sync 286 mV)
Defined with the color bar signal 100/0/75/0
Data transmission
Channel coding:
Scrambled NRZI
Transmission speed:
Input: 270 Mb/s
Amplitude:
0.8 Vp-p ؎10%
Cable length:
200 m max. (When using a Belden 8281,
Fujikura 5C2V or equivalent coaxial cable)
Digital input/output return loss:
15 dB or more (5 MHz to 270 MHz)
Signal forma:
525/625 component serial digital signal
conforming to SMPTE259M-C (ITU-R
BT.601/BT.656), 270 Mb/s
Video characteristics
Sampling frequency:
Y: 13.5 MHz R-Y, B-Y: 6.75 MHz
Composite signal: 27 MHz
Digitization:
8 bits (Only for the composite signals,
interpolating 8 bits to 10 bits.)
Bandwidth:
Y, R, G, B composite: 5 MHz
R-Y, B-Y: 2 MHz
Y, R-Y, B-Y phase error:
20 ns or less
K factor (2T pulse):
1% or less
Signal-to-noise ratio:
Y, R-Y, B-Y: 48dB or more
Composite signal: 54 dB or more
(when the lamp signal is input)
DG:
2% or less
DP:
2° or less
System delay:
Approx. 2.3 ms
EDH:
Conforms to SMPTE RP165
General
Power requirements:
+5 V DC: 1.0 A
(Supplied from the PFV-L Series Interface
Unit)
Operating temperature:
5 to 40 °C (41 to 104 °F)
Operating humidity:
10 to 90% (no condensation)
Dimensions
Board (H x D):
77 x 267 mm
(10 5/8 x 3 1/8 inches)
Connector panel (W x H):
33 x 85 mm
(1 5/16 x 3 3/8 inches)
Mass
Board:
Approx. 150 g (5 oz)
Connector panel:
Approx. 120 g (4 oz)
Service parts: Extension board (Part
No.A-8322-598-A), Maintenance manual
RE-
CLOCKING
SDI OUT x 4
525/625 COMPONENT SDI IN EDH
D/A
(FOR MONITORING)
COMPOSITE ANALOG VIDEO OUT x4
(NTSC/PAL)
or
Y/U/V + COMPOSITE ANALOG VIDEO OUT x 1
or
R/G/B + COMPOSITE ANALOG VIDEO OUT x 1
ACTIVE LOOP-THROUGH
82
Inter
face Pr
ocessor L Series
Interface Processor L Series
*SGC_0069-0098 02.3.16 5:03 PM Page 82