Sony 500WSPL - Manual (Page 68)

68
Chapter 3 Shooting
Chapter 3 Shooting
ClipLink Shooting
The ClipLink function is intended to be used at various
stages from recording to editing. When you record
using this function, Index Pictures are automatically
recorded along with the time code, scene number, and
other data, all of which make for more efficient
editing.
For an overview of the ClipLink function, see “What Is
ClipLink?” on page 136.
To record Index Picture, the optional DSBK-301A
Index Picture Board is required.
For detail of fitting the optional DSBK-301A, refer to the
instruction manual supplied with it.
Notes
• When an external equipment, such as VCR, is
connected to the DV OUT connector, you cannot
shoot with ClipLink.
• On the DSR-500WSL/500WSPL, you can also use
the ClipLink function without recording Index
Pictures. However, if you perform ClipLink shooting
on the DSR-500WSL/500WSPL without fitting the
optional DSBK-301A, the recorded tape may cause
malfunction at ClipLink continue on the DSR-1/1P.
When you perform ClipLink shooting in a system
containing the DSR-1/1P and DSR-500WSL/
500WSPL, fit the optional DSBK-301A Index Picture
Board to the DSR-500WSL/500WSPL.
1
Turn the power on and perform steps 2 to 10 in
“Basic Procedure for Shooting” (pages 49 and 50).
2
Perform the first two steps (page 53) in “Recording
on the Internal VCR”. Check the following points.
CLIP and IP appear in the display window.
2
2
3
∞
H MIN SEC FRM
1
dB
2
PB DATE NDF EXT-LK HOLD
CLIP
TAPE
BATT
DIAG
E F
RF SERVO HUMID SLACK
Li -
-40
-30
-12
0
IP CL CONT
OVER OVER WARNING
RESET
(MENU SET)
LIGHT
DISPLAY
ON
OFF
COUNTER
TC
U-BIT
-20
DVCAM
F 8 32k
F 8 48k
REC TIME SKIN DTL EXT VTR
OUTPUT
VTR
TRIGGER
AUDIO LEVEL
AUDIO SELECT
AUDIO IN
CH-1 LITHIUM BATT
MENU
TTL
DUR
ON
OFF
OFF
TTL RESET
PARALLE L
PRESET
DATE/TIME
F-RUN
REGEN
F-RUN
R-RUN
SET
INT ONLY
EXT ONLY
FRONT
VJ MIC
WRR
REAR
MIX
EXT
VBS
COMPONENT.
MONITOR SELECT
Y/C
SET
ClipLink
CONTINUE
ADVANCE SHIFT
CH-1
CH-2
FRONT MIC
LOW CUT
ON
OFF
MONITOR OUT
CHARACTER
ON
OFF
AUTO
MAN
CH-2
HYPER
GAIN
ON
OFF
SETUP
FILE
STD
Method
See “Menu 211 Selecting
the ClipLink Function”
under “VCR Menu
Operation” (page 109).
Check point
Check the ClipLink
function is on (or set it to
on).
Check whether or not the
cassette includes cassette
memory. (The camcorder
supports cassettes with up
to 16 Kbits of cassette
memory.) appears in the display
window when the loaded
cassette includes cassette
memory. (The ClipLink
function cannot be used
unless
appears in the
display window.)
Make sure that the lithium
battery has been correctly
inserted and is not used
up. Li appears in the display
window if the lithium
battery has not been
inserted or is used up.
Display Meaning
CLIP The camcorder is in ClipLink mode.
IP The camcorder is in ClipLink mode and can
record Index Pictures (when the DSBK-301A
is fitted).