Sunfire Radio - Manual (Page 46)

User's Manual
46
CHAPTER 5
DVD SAT VID1 VID2 VCR CD
DVD SAT VID1 VID2 VCR CD
DVD SAT VID1 VID2 VCR CD
PHONO DAT TAPE DAT TAPE
LEFT L SUR CEN LB SUR
FIXED MAIN ZON E2
PHONO DAT TAPE DAT TAPE
FIXED MAIN ZON
E2
RIGHT R SUR SUB RB SUR
MAIN VCR VID2/MON2
MAIN VCR VID2/MON2
MAIN VCR VID2/MON2
AUDIO/VIDEO OUT
PUTS
AUDIO INPUTS
AUDIO OUTPUTS
8-CHANNEL INP
UTS
STEREO OUTPUT
S
RIGHT
SURROUND RIGHT
MAIN
DVD SAT VID1 MAIN TRIGGERS
COMPONENT
OUT
COMPONENT VID
EO IN
Made in Snohomish, Washington, U.S.A.
LEFT LEFT SUR CENTER
SUB2 LB SUR
RIGHT RIGHT SUR
SUB1 SUB3
RB SUR
LINE LEVEL AU
DIO OUTPUTS
SPEAKER LEVE
L AU DVD
DVD
CD
SAT
DAT
VID1
VID2
SAT VID1 CD
Sun
Ultimate R
DIGITAL AUDIO IN
PUTS
Cr
Y
b C
L SIDE
R SIDE
SID
DIGITA
AM
GND
FM
75 Ω
R
L
R
L
R
L
COMP
VIDEO
S
VIDEO
AUDIO/VIDEO IN
PUTS
R
L
ZONE2
12VDC
12VDC
12VDC
MAIN ZONE
MON2
R
L
PHONO DAT TAPE DAT TAPE LEFT L SUR CEN LB SUR
FIXED MAIN ZON E2
PHONO DAT TAPE DAT TAPE
FIXED MAIN ZON E2
RIGHT R SUR SUB RB SUR
VCR VID2/MON2
AUDIO INPUTS
AUDIO OUTPUTS
8-CHANNEL INP
UTS
STEREO OUTPUT
S
LEFT LEFT SUR CENTER
SUB2 LB SUR
RIGHT RIGHT SUR
SUB1 SUB3 RB SUR
LINE LEVEL AU
DIO OUTPUTS
SPEAKER LEVE DVD
DVD
CD
SAT
DAT
VID1
VID2
SAT VID1 CD
Ultim
DIGITAL AUDIO IN
PUTS
b C
L
R
DI
R
R
L
R
L
R
L
ZONE
2
12VDC
R
L
Recording
Recording to a Tape Player
Input signals from an audio source playing in
the Receiver can be re cord ed using the left and
right audio outputs. The Tape player will receive
a straight copy of the analog source signal going
in, un af fect ed by the volume, tone or any sur-
round modes. If you are playing a digital source,
the tape player will receive a downmixed stereo
analog signal for recording.
• Turn OFF the Fully Automatic mode. This
is because some Tape decks, such as
three-head decks, will have an output
signal going into the Receiver during
recording. The DAT or TAPE inputs may
be in cor rect ly se lect ed as an input, rather
than the source you are trying to record.
• Manually select the source such as CD
and play it through your system.
• Set your Tape player to record, and adjust
the input levels for the best per for mance.
Once the levels are correct, you can reset
your source to the beginning and make
your re cord ing.
• Do not select another Main Zone input
while you are recording.
Recording to a VCR
Any video source playing in the Receiver
can be re cord ed using the left and right audio
and the video outputs. The VCR will receive
a straight copy of the source signal going in,
unaffected by the volume, tone or any surround
modes.
• Select the video source and play it
through your system.
• Set your VCR to record.
• Do not select another Main Zone source
while you are recording.
• The VID2/MON2 output can also be used
for recording, but Þ rst make sure that it
is set to VID2 in the VIDEO menu of the
OSD (see page 37). This output will then
mute to prevent feedback whenever the
VID2 input source is selected.
• Do not use the OSD while recording, as
the incoming video is shut off while the
OSD is displayed
RECORD
From Receiver
TAPE outputs
PLAY
To Receiver
TAPE inputs
RECORD
From Receiver
VCR outputs
PLAY
To Receiver
VCR inputs