Sony TA-FA777ES - Manual (Page 8)

8 GB
Additional Information
Troubleshooting
If you’ve experience any of the following difficulties while
using the amplifier, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
No sound output.
/ Connect the audio connecting cords firmly.
/ Connect the amplifier and other audio components
correctly.
/ Set SPEAKERS to ON (see page 6).
/ Turn INPUT SELECTOR to the appropriate
programme source.
No audio from one channel or unbalanced speaker
output.
/ Turn BALANCE to adjust the balance.
/ Check the speaker and input connections of silent
channel.
Sudden loss of audio and the POWER indicator lights up
red.
/ The speaker cords have been shorted. Make sure they
are connected correctly.
Weak bass or treble.
/ Adjust the TONE controls.
/ Press CARTRIDGE to select the appropriate cartridge
type (see page 5).
/ Change speaker positions or room conditions to
eliminate obstructions in sound path.
Distorted sound.
/ Improperly selected input signal.
/ Insufficient input capacity of speakers. Lower the
volume.
Lack of bass or ambiguity in instrument positions.
/ Speaker cord and terminal polarity are reversed.
Reconnect the cords with correct polarity.
Hum or noise.
/ Ground the turntable system (see page 5).
/ Connect the audio connecting cords firmly.
/ The amplifier is picking up interference from a TV set.
Move the amplifier away from the TV set or turn the
TV set off.
Cannot record.
/ Turn REC OUT SELECTOR to the appropriate
programme source.
/ Set REC OUT to ON (see page 7).
Specifications
System
Power Amplifier: Pure-complementary SEPP MOS FET
power amplifier with all stages
directly coupled
Preamplifier: Low-noise, high-gain equalizer
amplifier
Power section: Large-capacity power supply
advanced STD
Rated output 4 ohms, 150 W + 150 W (DIN 0.7%)
8 ohms, 100 W + 100 W (DIN 0.7%)
Speakers impedance 4 to 16 ohms
Output bandwidth (8 ohms) 10 Hz to 100 kHz (at 40 W output, and
high-frequency distortion rate of
0.08%)
Dynamic headroom at 4 ohms: 2 dB
at 8 ohms: 1.2 dB
Total harmonic distortion 0.005% (at 8 ohms, 10 W output)
Damping factor 100 (8 ohms, 1 kHz)
Intermodulation (IM) distortion (60 Hz:7 kHz=4:1)
0.005% (8 ohms)
Throughrate 125 V/ µ sec, 250 V/µ sec (Inside)
Residual noise Less than 115 µ V (network A)
Equalizer deviation PHONO MM: 20 Hz to 20 kHz,
±0.2 dB
Frequency response TUNER, SACD/CD, AUX, TAPE 1, 2,
3: 2 Hz to 100 kHz
+0
–3
dB
S/N PHONO MC: 78dB (A Fil, 0.5 mV)
MM: 87 dB (A Fil, 5 mV)
TUNER, SACD/CD, AUX, TAPE1, 2,
3: 105 dB
Inputs
Input sensitivity and impedance
PHONO MC: 0.25 mV, 100 ohms
MM: 2.5 mV, 50 kilohms
TUNER, SACD/CD, AUX, TAPE 1, 2,
3: 150 mV, 30 kilohms
Maximum input capability (1 kHz)
PHONO MC: 9 mV
MM: 150 mV
Outputs
Output level / impedance REC OUT 1, 2, 3: 150 mV,1 kilohms
PHONES: 10 mW (at 8 ohms)
Tone controls BASS (100Hz): ±7 dB
TREBLE (10kHz): ±6 dB
General
Power requirements 230 V AC, 50/60 Hz
Power consumption 330 W
Dimensions (approx.) (w/h/d) 430 Ч 175 Ч 455 mm
(17 Ч 7 Ч 17 15 /
16
inches)
incl. projecting parts and controls
Mass (approx.) 23 kg (50 lb 12 oz)
Supplied accessories Mains cable (1)
Design and specifications are subject to change without notice.