Siemens WTXD5522UC - Manual (Page 10)

10
The door catch can be reversed if
necessary. The door is hinged on the
right at the factory.
Pedestal Mounting Kit
part no. WZ 20395
If mounting the dryer on the Siemens
pedestal follow the instructions
supplied with the Pedestal.
Mobile home kit
part no. WZ 20375
Note:
Please check with the Authority Having
Jurisdiction in your area to verify if a gas
dryer can be installed in your mobile
home. Once that has been verified,
installation of the dryer shall conform to
the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part
3280 {formerly the Federal Standard for
Mobile Home Construction and Safety,
Title 24, HUD (Part 280)}, and/or
Standard CAN/CSAĆZ240 MH.
Please use mobile home kit number
WZ 20375 for means to secure the
dryer to the structure.
See page 9 Exhaust Air Connection"
for the exhaust duct installation
instructions.
The exhaust duct must be securely
fastened to a noncombustible portion
of the mobile home structure and must
not terminate beneath the mobile
home.
An opening to the outside must be
provided during installation. Insure that
the free area of the opening for the
introduction of outside air is not less
than twice the area of the dryer exhaust
outlet or use at least a 5 inch diameter
exhaust or at least a 25 in 2 square
exhaust duct for the opening.
Installation ć step by step
1. Unpack the dryer.
2. Remove all objects from the drum.
3. Check the dryer for visible
damage.
4. Position the dryer near the
installation location.
5. If required, have customer service
change the door hinges to the left
(see page 6).
6. If required, have customer service
install the exhaust air outlet on the
dryer (see page 8).
7. Have the gas supply connected by
an qualified technician (see page
7).
8. Install exhaust duct, if necessary.
Follow the installation instructions
supplied by the appropriate
manufacturer!
i If space is very restricted, it is
recommended to fit the initial parts
of the exhaust duct to the dryer
before the dryer is moved to its
final installation location.
9. Move the dryer to its final location
and align.
ATTENTION
Do not slide dryer across the floor if
heightĆadjustable feet have been
extended. Feet and/or dryer base
may be damaged if dryer is slid
across floor with heightĆadjustable
feet extended.
10. Position and then level the dryer .
The dryer should be level with all
four feet firmly on the ground. The
dryer must not wobble. If the dryer
is not level or if it does wobble, the
feet must be adjusted. Adjust the
heightĆadjustable feet until the
dryer does not rock and is level,
both frontĆtoĆback and
sideĆtoĆside.
11. Connect the exhaust duct to the
exhaust air outlet on the dryer.
12. Insert plug into the wall receptacle.
Check list before using
the dryer
1. Check that steps 1-12 have been
implemented properly.
2. Ensure that the dryer is connected
to the power supply.
3. Open the shutoffĆvalve.
4. Read the operating instructions to
understand how your dryer
operates.
5. Conduct an appliance test:
q Check that the drum is empty.
q Close the dryer door.
q Switch the dryer to extra dry"
and then press the Start
button.
q After 3-5 minutes press the
Stop button and open the door.
6. If the interior of the dryer feels
warm, the dryer has been
connected properly.
Switch the dryer to off".
7. If the dryer does not work, switch
the dryer to off".
Look in the troubleshooting
section (page 21) of the
OPERATING INSTRUCTIONS and
find the fault.
Preparing to transport the
dryer ć step by step
1. Close the shutĆoff valve.
2. Rotate the program selector to
off".
3. Pull out the power supply plug
or
turn off the circuit breaker.
4. Disconnect gas supply
5. Disconnect the exhaust duct from
the exhaust air outlet on the dryer.
6. Place any accessories in the drum.
7. Close the door and secure with
adhesive tape.
8. Screw the heightĆadjustable feet of
the dryer into the housing to
prevent them from being damaged
during transportation.